Ting Yang

Prof. Dr. Ting Yang


Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
30 November 2021 in Coatings
Verified
Journal Article
Open access
PDF file
ZYZining Yang
Zining Yang
WWWeize WANG
Weize WANG
SDShujuan Deng
Shujuan Deng
HFHuanjie Fang
Huanjie Fang
TYTing Yang
Ting Yang
TYTing Yang
Ting Yang
Gadolinium zirconate with excellent high-temperature phase stability and sintering resistance has become a very promising candidate material for a new generation of thermal barrier coatings (TBCs). However, the low fracture toughness of gadolinium zirconate greatly limits its application. In this study, gadolinium zirconate (GZ) and two kinds of toughened gadolinium zirconate (GZ/YSZ prepared by mixed powder of Gd2Zr2O7 and YSZ and GSZC prepared by (Gd0.925Sc0.075)2(Zr0.7Ce0.3)2O7 powder) double-layered TBCs were prepared by atmospheric plasma spraying (APS). The fracture toughness of the GZ/YSZ coating and GSZC coating were 9 times and 3.5 times that of GZ coating, respectively. The results of thermal shock test showed that the three TBCs exhibit different failure mechanisms. During the thermal shock test, cracking occurred at the interfaces between the YSZ layer and the BC or GZ/YSZ layer, while GSZC TBC failed due to premature cracking inside the GSZC layer. The particle erosion rate of the GZ, GZ/YSZ, and GZSC coatings were 1.81, 0.48, and 1.01 mg/g, respectively, indicating that the erosion resistance of coatings is related to their fracture toughness. Furthermore, the superior erosion resistance of the GZ/YSZ and GSZC coatings can be attributed to the conversion of crack propagation path during the erosion test.

10 May 2022 in Coatings
Verified
Journal Article
Open access
PDF file
YWYihao Wang
Yihao Wang
ZXZhenning Xu
Zhenning Xu
WWWeize WANG
Weize WANG
CZChengcheng Zhang
Chengcheng Zhang
ZYZexin Yu
Zexin Yu
TYTing Yang
Ting Yang
Solution precursor plasma spray (SPPS) can prepare thermal barrier coatings (TBCs) with nanostructures, which can modify the adhesion and wettability of molten silicate environmental deposits (CMAS) on the surface of TBCs, thereby improving the resistance of TBCs to CMAS corrosion. In this study, SPPS layers with micro-nano double scale structures were prepared on the surface of conventional atmospheric plasma spraying (APS) coatings. The effect of process parameters on the micro-nano double scale structures and the wetting and infiltration behavior of molten CMAS on the surface of coatings were investigated. The results show that micron structure is more sensitive to process parameters. Lower precursor viscosity, closer spraying distance, and smoother APS layer are favorable to form more typical and dense micron structures. After covering the SPPS layer, the CMAS wetting diameter is reduced by about 40% and the steady-state contact angle increased up to three times. The reason is that the micro-nano double scale structures can effectively trap air and form an air layer between the coating surface and the molten CMAS. In addition, nano-particles play a more important role in the formation of the air layer, which in turn determines the steady-state wettability properties. While micron structures can influence the time needed to reach the steady state. However, the SPPS layers composed of nano-particles have a very loose structure and weak cohesion, and they degrade and fail rapidly after the infiltration of molten CMAS. Therefore, maintaining the excellent CMAS wetting resistance of the SPPS layers while taking into account their lifetime and reliability has become the focus of further research.

9 June 2022 in Coatings
Verified
Journal Article
Open access
PDF file
ZYZining Yang
Zining Yang
KYKai Yang
Kai Yang
WWWeize WANG
Weize WANG
TYTing Yang
Ting Yang
HFHuanjie Fang
Huanjie Fang
CZChengcheng Zhang
Chengcheng Zhang
Gadolinium zirconate (GZ) has become a promising thermal barrier coating (TBC) candidate material for high-temperature applications because of its excellent high-temperature phase stability and low thermal conductivity compared to yttria-stabilized zirconia (YSZ). The double-ceramic-layered (DCL) coating comprised of GZ and YSZ was confirmed to possess better durability. However, the particle-erosion resistance of GZ is poor due to its low fracture toughness. In this study, a novel erosion-resistant layer, an Al2O3-GdAlO3 (AGAP) amorphous layer, was deposited as the top layer to resist erosion. Three triple-ceramic-layer (TCL) coatings comprised of an Al2O3-GAP layer as the top layer, a GZ layer, a GZ/YSZ composite layer, and a rare-earth-doped gadolinium zirconate (GSZC) layer as the intermediate layer, and a YSZ layer as the base layer. For comparison, an AGAP-YSZ DCL coating without a middle layer was prepared as well. Under the erosion speed of 200 m/s, only a small amount of spallation occurred on the surface of the Al2O3-GAP layer, indicating a superior particle-erosion resistance. In the thermal shock test, the Al2O3-GAP layer experienced glass transition and the glass transition temperature was close to 1500 °C. The hardness of the Al2O3-GAP coating after glass transition increased ~170% compared to the as-sprayed Al2O3-GAP coating. Moreover, The DCL TBC and TCL TBCs exhibited different failure mechanisms, which illustrated the necessity of the middle layer. The finite element model (FEM) simulation also shows that the introduction of the GZ layer can obviously reduce the thermal stress at the TC/BC interface. In terms of coating with a modified GZ layer, the AGAP-GZ/YSZ-YSZ coating and AGAP-GSZC-YSZ coating showed a similar failure model to the AGAP-GZ-YSZ coating, and the AGAP-GSZC-YSZ coating exhibited better thermal shock resistance.

5 December 2022 in Coatings
Verified
Journal Article
Open access
PDF file
HZHan Zhu
Han Zhu
WWWeize WANG
Weize WANG
DYDongdong Ye
Dongdong Ye
TYTing Yang
Ting Yang
DLDongpeng Li
Dongpeng Li
YWYihao Wang
Yihao Wang
High-emissivity coatings are often used on the surfaces of solar probes to block heat from the sun. Therefore, improving the thermal control ability is the standard for determining the quality of the coatings. In this study, MgO was doped into Al2O3 to improve the thermal control ability of the coatings and to analyse the effect of different MgO doping contents. The solar absorptivity to infrared (IR) emissivity ratio (α/ε) was used to evaluate the thermal control ability of the coatings. The results showed that 5 wt.% MgO doping content is the best choice. The main reason for the change in α/ε is related to the doping of MgO, which affects the grain size of Al2O3.

23 May 2026 in Materials
Verified
Journal Article
Open access
PDF file
JHJibo HUANG
Jibo HUANG
TYTing Yang
Ting Yang
CZCheng Zhou
Cheng Zhou
Zhaoguo QiuZhaoguo Qiu
Zhaoguo Qiu
TiN coatings have been widely employed in cutting tools due to their high hardness and excellent wear resistance. While most research on nitride coatings has focused on binary (e.g., TiN) and ternary (e.g., TiAlN, TiSiN) systems, the quaternary TiMoSiN system remains comparatively underexplored. In response to the growing demand for comprehensive coating performance under increasingly complex working conditions, this work incorporates Mo and Si into the TiN system to synergistically enhance mechanical, tribological, and corrosion-resistant properties. TiMoSiN coatings were deposited onto cemented carbide substrates by arc ion plating using a Ti0.8Mo0.1Si0.1 alloy target. The influence of nitrogen partial pressure (0.2–1.7 Pa) on the microstructure, mechanical properties, tribological behavior, and electrochemical corrosion performance was investigated. The results show that nitrogen partial pressure plays a critical role in regulating the chemical composition, phase structure, and preferred orientation of the coatings. As the nitrogen partial pressure increases, surface macroparticles are reduced, while the Ti and Mo contents decrease and the Si and N contents increase. The phase structure evolves from a dual-phase mixture of TiN and Ti2N to a single TiN phase, accompanied by a shift in preferred orientation from (111) to (200). The hardness of the coatings ranges from 36.2 to 43.1 GPa, reaching a maximum of 43.1 GPa at 1.0 Pa. The coating deposited at 0.6 Pa exhibits the best overall performance: it achieves the lowest friction coefficient (0.349) and wear rate (1.08 × 10−7 mm3/(N·m)), together with the highest corrosion resistance, as reflected by the most noble corrosion potential (−152 mV) and the lowest corrosion current density (8.99 × 10−8 A·cm−2). This study demonstrates that nitrogen partial pressure effectively controls the microstructure and multifunctional properties of TiMoSiN coatings, providing practical process guidelines for their application in demanding cutting environments.

31 December 2024 in Coatings
Verified
Journal Article
Open access
PDF file
DYDongdong Ye
Dongdong Ye
SXShuheng Xu
Shuheng Xu
ZXZhou Xu
Zhou Xu
JPJiabao Pan
Jiabao Pan
CYChangdong Yin
Changdong Yin
JHJibo HUANG
Jibo HUANG
The distribution morphology and density of micro-agglomerated particles are the main microstructural characteristics of embedded micro-agglomerated particle thermal barrier coatings. The study of their effect on the sintering resistance of coatings can help to further improve the service life of thermal barrier coatings. Strain tolerance and thermal insulation performance are important evaluation indicators for the sintering resistance of thermal barrier coatings. In this study, embedded micro-agglomerated particle thermal barrier coatings were prepared by plasma spraying, and the distribution morphology and density of micro-agglomerated particles were analyzed and counted. Different simulation models were established to analyze the compressive stress and thermal stress of the coating, as well as the influence of the microstructure characteristics on the strain tolerance and thermal insulation performance of the coating. A machine learning model was established to evaluate the nonlinear relationship between the microstructure characteristics of the coating and its strain tolerance and thermal insulation performance. The results show that the horizontal angle of the micro-agglomerated particles in the coating has the most significant effect on the sintering resistance and is predicted using the PSO-SVM machine learning model. The predicted effects are the most important, and the coefficients of determination for strain tolerance and thermal insulation are as high as 0.988 and 0.945, respectively, indicating a strong correlation between the predicted and actual values. This research technique used experimental research-simulation computation-machine learning can be used to optimize the microstructure of coatings and guide the preparation of high-performance thermal barrier coatings.