Wood-based materials are used extensively in residual construction worldwide. Most of the adhesives used in wood-based materials are derived from fossil resources, and some are not environmentally friendly. This study explores nanofiber technology as an alternative to such adhesives. Previous studies have shown that the three-dimensional binding effects of cellulose nanofiber (CNF), when mixed with wood flour, can significantly improve the physical and mechanical properties of wood flour board. In this study, ligno-cellulose nanofibers (LCNF) were fabricated by wet disk milling of wood flour. Composite boards of wood flour and LCNF were produced to investigate the binding effect(s) of LCNF. The fabrication of LCNF by disk milling was simple and effective, and its incorporation into wood flour board significantly enhanced the physical and mechanical properties of the board.
The demand for wood-based materials as an alternative to plywood is increasing, and a synthetic adhesive is typically used for the fabrication of such materials. The identification of replacements for standard adhesives poses a major challenge. In this study, we investigated the mechanical properties of particleboard bonded by cellulose nanofiber (CNF) and compared the mechanical properties of particleboard bonded by CNF with those of particleboard bonded by adhesive. CNF was added together with wood particles during the fabrication process. The target CNF addition amounts were 0, 3, 5, 10, and 20 weight percent. The bending and internal bond strengths of the particleboard with CNF increased, and its water absorption decreased as CNF content increased. The comparison between the boards prepared with adhesives and those with CNF showed that the properties of boards prepared with 20 weight percent CNF were comparable to those of boards prepared with 1 weight percent synthetic adhesive.
Recently, the usage of wood–plastic composite (WPC) products has increased, mainly for exterior decking. The shape of fillers is one of the important factors deciding the mechanical and physical properties of WPCs. Surface-fibrillated wood flour (WF) improves the mechanical properties of WPCs, although it requires a lot of energy and time to produce the fibrous structure during the pulverization process. Therefore, the adsorptive interaction between cellulose nanofiber (CNF) and WF by hydrogen bonding was investigated. We considered that CNF could form the fibrous structures on the WF surface by mixing CNF and WF. Also, it is thought that the addition of CNF could increase mechanical and physical properties of WPC because CNF has better physical and mechanical properties than most other fibers. The objective of this study was to produce WF-CNF fillers and to evaluate the mechanical and physical properties of WPCs containing WF-CNF fillers. WF-CNF fillers could be produced by freeze-drying after mixing WF, CNF, and water. The fibrous structures on the WF surface were observed through scanning electron microscope images of WF-CNF filler containing 3 weight percent CNF. A WPC with WF-CNF filler containing 22 percent (by weight) WF and 3 percent (by weight) CNF showed improved mechanical properties compared with WPCs without CNF. The water absorption of WPCs containing CNF was found to decrease with increasing CNF content.
14 June 2017 in Journal of Near Infrared Spectroscopy
To improve the recycling rate of wooden materials, it is necessary to classify wood waste by disposal method and usage. In the industrial manufacture of these materials, rapid and accurate determination of their chemical and physical properties is critical for a stable supply of wood products with reliable quality. In this study, we investigated a discriminant analysis process for waste wood products using hyperspectral imaging with a newly developed repetitive principal component analysis. Hyperspectral images of four types of wood waste (plywood coated with resin, preservative-treated wood, hardwood and softwood) were acquired. The mean spectrum of each sample was extracted from a hypercube in order to build a classification model. A novel classification method based on principal component analysis, named repetitive principal component analysis, was developed. A total of three repetitions of principal component analysis were performed to classify the four types of wood waste. Cross-validated results of repetitive principal component analysis resulted in classifications greater than 85% for any of the four wood waste types. The discriminant model was then applied to single-pixel spectra of the hypercube to form a prediction map. Hyperspectral imaging, with the aid of the new repetitive principal component analysis discriminant analysis, is a powerful tool in wood recycling processes.
The objective of this study was to investigate the lab-scale manufacturing process of insulation fiberboard (IFB) with cellulose nanofibers (CNFs) and evaluate the effects of CNFs on the mechanical and physical properties of the IFB. Because the fabricated IFBs with CNFs had a homogeneous appearance, it was assumed that CNFs can be easily dispersed within IFB by adding them during the mixing stage of the wet process of wood-based board production. The results for the IFBs with CNFs revealed that the density and bending properties increased, while the thickness decreased with an increase in the CNF addition ratio. Furthermore, after the water absorption test, the weight change rates of the IFBs decreased, and the thickness swelling rates increased. Although the size of the specimens was different from the size in JIS A 5905 (Japan Standards Association 2014), the modulus of rupture (MOR) values of IFBs with a target density more than or equal to 0.20 g/cm3 were higher than the value of A-class IFB in the standard for all CNF addition ratios. In addition, lower thermal conductivity may be realized under similar MOR values by adding CNFs to IFB. On the other hand, to produce CNF-reinforced IFBs with target density/thickness, it is necessary to develop a method for decreasing the cohesive force derived from CNF aggregation and the compressive force originating from the water surface tension caused by the high water retention of CNFs.