This article presents the design, experimental results, and modeling of an inversion-mode CMOS varactor integrated in the STMicroelectronics 55-nm BiCMOS technology. The device was characterized from 1 to 325 GHz, demonstrating high-quality factor at millimeter-waves. For instance, a quality factor of 7 at around 190 GHz for a tuning ratio (Cmax/Cmin) greater than 4 was measured. This performance overpasses that of accumulation-mode varactors usually provided in CMOS technologies design kits, for frequencies beyond about 100 GHz. In addition, a small-signal electrical model is provided from 100 to 250 GHz.
In this Letter, we propose an approach to improve the packaging of electro-optical transceivers based on silicon photonics through the development of a glass interposer. This assembly platform integrates polymer optical waveguides and an integrated turning mirror that vertically redirect the optical signal in the plane of the interposer to the grating coupler of a flip-chipped photonic integrated circuit (PIC). A distinctive feature of the proposed packaging scheme is to use a conventional flip-chip technique without active alignment. Functionalities are completed with a copper redistribution layer that supports the routing of DC to millimeter wave (mmW) signals to drive the PIC. The measured loss in polymer waveguides is 1.92 dB/cm at 1310 nm, and the coupling losses associated with light propagation through the turning mirror and the PIC grating coupler are 18.7 dB. Coplanar mmW waveguides are structured on the glass interposer by cold laser ablation, yielding an attenuation of 0.3 dB/mm at 58 GHz. The most important outcome of this work is that the coupling of the optical signal from the interposer to the PIC is experimentally established. We also assessed the mmW performance of coplanar waveguides through the validation of the interposer to PIC and PIC to the interposer transition.
With the evolution of radio frequency (RF)/microwave technology, there is a demand for circuits that are able to meet highly challenging RF front end specifications. Silicon-on-insulator (SOI) technology is one of the leading platforms for upcoming wireless generation. The degradation of performance due to substrate coupling is a key problem to address for telecommunication circuits, especially for the high throw count switches in RF front ends. In this context, a fast, flexible and local laser ablation technique of the silicon handler allows for the membrane suspension of large millimeter-scale circuits. This approach enables the evaluation of the ultimate performance in the absence of the substrate, i.e., without dissipative losses and substrate-induced non-linear effects, on capacitive comb coupling structures and RF switches. Compared to high-resistivity SOI substrates, the high frequency characterization of RF membrane switches reveals a superior linearity performance with a reduction in second and third harmonics by 17.7 dB and 7.8 dB, respectively. S-parameter analysis also reveals that membrane suspension entails insertion losses that are improved by 0.38 dB and signal reflection lowered by 4 dB due to a reduced off-state capacitance. With reference to a trap-rich substrate, the membrane suspension also achieves an additional 7.8 dB reduction in the second harmonic, indicating that there is still scope for improvement in this figure of merit. The obtained results demonstrate a new way to evaluate optimized circuit performance using post-fabrication substrate engineering.
This paper presents a fully integrated E-band (83/95 GHz) diplexer realized in STMicroelectronics’ BiCMOS 55 nm technology. The design directly addresses the critical trade-off between miniaturization and the performance required for high-frequency on-chip systems. The key innovation is a novel patch resonator optimally exploiting the multi-layer structure of the technology’s Back-End-Of-Line. It achieves significant compactness by jointly combining two distinct miniaturization techniques: slotted structures and mushroom-type capacitive loading. This method results in an impressive 77% size reduction compared to conventional designs. Furthermore, we introduce precisely controlled transmission zeros (TZs) to maximize inter-band isolation. The fabricated diplexer achieves a remarkably narrow fractional bandwidth (FBW) of 8.2%—the lowest reported to date for integrated BiCMOS/CMOS E-band implementations—and a robust inter-band isolation exceeding 25 dB, while demonstrating excellent return loss (better than 25 dB). Hence, this work validates a highly compact and scalable approach for integrated E-band transceivers, paving the way for future 6G front-end applications.