xiangguang han

xiangguang han


Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
29 November 2024 in Microsystems & Nanoengineering
Verified
Journal Article
Open access
PDF file
RTRenjie Tan
Renjie Tan
YXYong Xia
Yong Xia
XHxiangguang han
xiangguang han
LHLinya Huang
Linya Huang
WGWendi Gao
Wendi Gao
Libo ZhaoLibo Zhao
Libo Zhao
Miniaturized six-axis force/torque sensors have potential applications in robotic tactile sensing, minimally invasive surgery, and other narrow operating spaces, where currently available commercial sensors cannot meet the requirements because of their large size. In this study, a silicon-based capacitive six-axis force/torque sensing chip with a small size of 9.3 × 9.3 × 0.98 mm was designed, fabricated, and tested. A sandwich decoupling structure with a symmetrical layered arrangement of S-shaped beams, comb capacitors, and parallel capacitors was employed. A decoupling theory considering eccentricity and nonlinear effects was derived to realize low axial crosstalk. The proposed S-shaped beams achieved a large measurement range through stress optimization. The results of a coupled multiphysics field finite-element simulation agreed well with those of theoretical analyses. The test results show that the proposed sensing chip can detect six-axis force/torque separately, with all crosstalk errors less than 2.59%FS. Its force and torque measurement ranges can reach as much as 2.5 N and 12.5 N·mm, respectively. The sensing chip also has high sensitivities of 0.52 pF/N and 0.27 pF/(N·mm) for force and torque detection, respectively.

23 July 2024 in Microsystems & Nanoengineering
Verified
Journal Article
Open access
PDF file
MHMimi Huang
Mimi Huang
XWXiaoyu Wu
Xiaoyu Wu
Libo ZhaoLibo Zhao
Libo Zhao
XHxiangguang han
xiangguang han
YXYong Xia
Yong Xia
ZJZhuangde Jiang
Zhuangde Jiang
Hydraulic technology with smaller sizes and higher reliability trends, including fault prediction and intelligent control, requires high-performance temperature and pressure-integrated sensors. Current designs rely on planar wafer- or chip-level integration, which is limited by pressure range, chip size, and low reliability. We propose a small-size temperature/high-pressure integrated sensor via the flip-chip technique. The pressure and temperature units are arranged vertically, and the sensing signals of the two units are integrated into one plane through silicon vias and gold–gold bonding, reducing the lateral size and improving the efficiency of signal transmission. The flip-chip technique ensures a reliable electrical connection. A square diaphragm with rounded corners is designed and optimised with simulation to sense high pressure based on the piezoresistive effect. The temperature sensing unit with a thin-film platinum resistor measures temperature and provides back-end high-precision compensation, which will improve the precision of the pressure unit. The integrated chip is fabricated by MEMS technology and packaged to fabricate the extremely small integrated sensor. The integrated sensor is characterised, and the pressure sensor exhibits a sensitivity and sensitivity drift of 7.97 mV/MPa and −0.19% FS in the range of 0–20 MPa and −40 to 120 °C. The linearity, hysteresis, repeatability, accuracy, basic error, and zero-time drift are 0.16% FS, 0.04% FS, 0.06% FS, 0.18% FS, ±0.23% FS and 0.04% FS, respectively. The measurement error of the temperature sensor and temperature coefficient of resistance is less than ±1 °C and 3142.997 ppm/°C, respectively. The integrated sensor has broad applicability in fault diagnosis and safety monitoring of high-end equipment such as automobile detection, industrial equipment, and oil drilling platforms.

12 September 2022 in IEEE Transactions on Industrial Electronics
Verified
Journal Article
Closed access
WGWendi Gao
Wendi Gao
CLCunlang Liu
Cunlang Liu
XHxiangguang han
xiangguang han
Libo ZhaoLibo Zhao
Libo Zhao
QLQijing Lin
Qijing Lin
DSDong Sun
Dong Sun
Precise force sensing is essential for the mechanical characterization and robotic micromanipulation of biological targets. In this work, a high-resolution microelectromechanical system capacitive force sensor is proposed for measuring ultralow multiphysics. A bionic swallow structure that contained multiple feathered comb arrays is designed for reducing chip dimension and eliminating undesirable mechanical cross-coupling effect. The comb structure is optimized for maximum sensitivity, linearity, and compact chip size. Utilizing a novel interconnection configuration, interferences derived from parasitic capacitance and electrostatic forces exerted negligible effects on the sensor output. The proposed bionic force sensor is fabricated following a simple three-mask process and integrated with application-specific integrated circuit readouts. Its measuring sensitivity is 7.151 fF/nm, 0.529 aF/nN, and 4.247 pF/g for displacement, force, and inclination measurements, respectively. The proposed sensor has a large measurement range of 1000.00 nm and 13.83 μN with a high linearity of 0.9998. The 1-σ resolution is 0.0328 nm and 0.4436 nN, and the noise floor resolution is 0.0044 nm $\sqrt {\mathbf{Hz}} $ and 0.0597 nN/ $\sqrt {\mathbf{Hz}} $ for displacement and force measurements, respectively. The bias stability of Allan deviance is 0.0050 nm and 0.0678 nN at an integration time of 0.65 s. The proposed bionic swallow sensor exhibits considerable improvement over existing capacitive sensors and feasibility for ultralow multiphysics measurement in biomedical applications.

15 July 2024 in IEEE Sensors Journal
Verified
Journal Article
Closed access
MHMimi Huang
Mimi Huang
XHxiangguang han
xiangguang han
Libo ZhaoLibo Zhao
Libo Zhao
SFShu Fan
Shu Fan
YXYong Xia
Yong Xia
XHXiaowei Hou
Xiaowei Hou
Sensor research is currently focused on integration, downsizing, and lightweightness to satisfy the demands of high-end equipment for intelligence, so we design a MEMS integrated sensor. This paper describes the design of a MEMS temperature and pressure integrated sensor with a back-inlet packaging. Glass slurry sintered back-inlet packaging is used to increase the sensor’s dielectric compatibility and connection strength. The ideal size is established after simulating and optimizing the chip’s major dimensions. Processes including laser welding, sintering, and MEMS fabrication technology finish the packing and preparation of the sensor chip. The encapsulated structure can withstand a 30 MPa pressure test. Finally, the pressure unit exhibits a sensitivity and sensitivity drift of 5.536 mV/MPa and -0.1900%FS in the range of 0-15 MPa and -40-120 °C, respectively. The linearity, hysteresis, repeatability, basic error, accuracy and zero-time drift are 0.2094%FS, 0.1987%FS, 0.1885%FS, ±0.4507%FS, 0.3244%FS and 0.1985%FS, respectively, and the measurement error of the temperature unit is less than ±0.61 °C.

1 April 2025 in IEEE Sensors Journal
Verified
Journal Article
Closed access
YLYang Lv
Yang Lv
SXShaolong Xu
Shaolong Xu
XHXiaowei Hou
Xiaowei Hou
MYMingzhi Yu
Mingzhi Yu
QLQunxin Liu
Qunxin Liu
JXJingfeng Xiong
Jingfeng Xiong
High-g accelerometers are the core devices for high-impact signal measurement, and microelectromechanical systems (MEMS) piezoresistive accelerometers, as the mainstream technological solution for high-g accelerometers, have serious mutual constraints on their sensitivity and natural frequency. In order to overcome the above problems, this paper proposed a MEMS accelerometer with a range of 100000g based on the pure axial deformation of piezoresistive beam. While ensuring the natural frequency of the accelerometer, the natural frequency of the sensor is substantially increased. Moreover, the structure does not require complex theoretical calculations to realize the pure axial stress state, which greatly simplifies the design process. The test results show that the proposed accelerometer has a natural frequency greater than 1 MHz and a sensitivity of 2.47 μV/g/5V, which indicates that the proposed accelerometer has high performance and can meet the needs in the field of high-impact signal measurement.

26 September 2023 in Measurement Science and Technology
Verified
Journal Article
Closed access
MYMingzhi Yu
Mingzhi Yu
CJChen Jia
Chen Jia
XHxiangguang han
xiangguang han
YXYong Xia
Yong Xia
Libo ZhaoLibo Zhao
Libo Zhao
ZJZhuangde Jiang
Zhuangde Jiang
Microfabricated piezoresistive accelerometers with purely axially deformed piezoresistive beams have demonstrated high performance. However, the conventional design of such accelerometers requires complex theoretical calculations and specific dimensional conditions to achieve purely axial deformation, which inevitably increases the difficulty and cost of the design and manufacturing. We propose an innovative structure that can simply realize pure axial deformation of piezoresistive beams by eliminating the transverse displacement at both ends without tedious calculations. An accelerometer based on the structure was fabricated; both static and dynamic performances were tested. The results showed that the accelerometer had high sensitivity (2.44 mV g −1 with 5 V bias, without circuit amplification), low cross-axis sensitivity (1.56% and 0.49 %, respectively), and high natural frequency (11.4 kHz), with a measurement range of 0–100 g. This design method provides an easy approach for designing high-performance piezoresistive sensors.