Sergei V. Aliukov

Dr. Sergei V. Aliukov


Research Focus & Metrics

Academic Career Length

1Year (2026-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 November 2026 in Machines
Verified
Journal Article
Open access
PDF file
Evgeny SolominEvgeny Solomin
Evgeny Solomin
HSHanna E. Shahin
Hanna E. Shahin
Osintsev KonstantinOsintsev Konstantin
Osintsev Konstantin
SASergei V. Aliukov
Sergei V. Aliukov
PDPavel A. Drogovoz
Pavel A. Drogovoz
ASAlexander N. Shishkov
Alexander N. Shishkov
Pneumatic systems are widely used in industry; however, compressed air remains an expensive energy source. To save energy, supply pressure is often reduced, but this leads to insufficient pressure in specific sections of the pneumatic circuit that require higher pressure. Pneumatic pressure boosters (PPBs) are used to address this issue, yet traditional designs lose a significant amount of energy during the exhaust phase. This paper proposes a pressure booster with energy recovery (PPB-R), in which the energy of the exhaust air is directed into an additional expansion chamber to perform useful work by moving the piston. A comparative numerical analysis of the energy efficiency of the PPB and PPB-R was conducted using the “air power” method. A mathematical model of the system was developed, incorporating force and mass flow balance equations under an isothermal assumption, with friction forces estimated from experimental data. The results indicate that the energy efficiency of the PPB-R may exceed that of the standard PPB by 3–6%, and its boost ratio improvement increases from about 3% at 200 kPa to 13% at 800 kPa. Furthermore, optimal expansion chamber diameters were determined for different supply pressures (85, 95, and 110 mm at 300, 500, and 800 kPa, respectively). The established pressure–flow characteristics confirm that the PPB-R maintains a nearly constant relative pressure advantage of about 15% under all load conditions. A quantitative energy balance shows that approximately 66% of the recovered energy is converted into additional useful output. The practical significance of this work lies in the potential to reduce compressor outlet pressure (thereby saving electricity) or to increase pressure at the point of use without increasing air consumption. The findings can be applied to the design and modernization of industrial pneumatic systems.

22 October 2026 in Energies
Verified
Journal Article
Open access
PDF file
Zaid Salah AL HaydriZaid Salah AL Haydri
Zaid Salah AL Haydri
Osintsev KonstantinOsintsev Konstantin
Osintsev Konstantin
SASergei V. Aliukov
Sergei V. Aliukov
PDPavel A. Drogovoz
Pavel A. Drogovoz
ASAlexander Николаевич N. Shishkov
Alexander Николаевич N. Shishkov
NPNikita Pshenisnov
Nikita Pshenisnov
In hot arid climates, combined cycle power plants (CCPPs) can experience reduced performance as high ambient temperature increases compressor inlet temperature and specific compression work. This study develops a steady-state energy, exergy, and exergoeconomic model of a 750 MW CCPP integrated with an ice thermal energy storage (ITES) cooling subsystem under Basra, Iraq, climatic conditions. Four configurations are evaluated: a standard plant without cooling, compressor-inlet cooling, air-cooled-condenser (ACC) inlet cooling, and simultaneous dual-point cooling of the compressor and ACC inlet air. Twelve monthly meteorological conditions are used to characterize the seasonal operating envelope, while the annual-mean condition is used for the comparative optimization. Four objective functions are evaluated through independent single-objective genetic-algorithm (GA) runs: minimization of total operating cost rate, minimization of fuel cost rate, maximization of thermal efficiency, and maximization of exergy efficiency. The reported optimization results are therefore objective-specific rather than a single Pareto multi-objective optimum. At the common total-operating-cost objective, the reported optimum gives 9.468 × 10−3 USD/s for Case 2, 8.993 × 10−3 USD/s for Case 3, and 8.993 × 10−3 USD/s for Case 4, compared with 9.721 × 10−3 USD/s for the standard case. Under the corresponding Case-3 and Case-4 total-cost runs, the thermal efficiency is 49.44%, compared with 48.86% for the standard case. Exergy analysis shows that the combustion chamber remains the dominant source of exergy destruction. The results quantify the thermodynamic and economic effects of the alternative cooling configurations within the adopted steady-state model, while the transient charge/discharge behavior of the ITES tank remains outside the present model boundary.

17 September 2026 in Energies
Verified
Journal Article
Open access
PDF file
Zaid Salah AL HaydriZaid Salah AL Haydri
Zaid Salah AL Haydri
Osintsev KonstantinOsintsev Konstantin
Osintsev Konstantin
SASergei V. Aliukov
Sergei V. Aliukov
PDPavel A. Drogovoz
Pavel A. Drogovoz
ASAlexander N. Shishkov
Alexander N. Shishkov
NPNikita Pshenisnov
Nikita Pshenisnov
This study numerically investigates unsteady natural convection and Soret–Dufour double-diffusion in a two-dimensional sinusoidally wavy porous cavity saturated with an Al2O3–Cu/Water hybrid nanofluid (φ = 0.02), using a Darcy–Brinkman formulation with temperature-dependent viscosity and Rosseland thermal radiation. The governing equations are solved on a boundary-fitted grid; an independent Method of Manufactured Solutions verification confirms second-order accuracy, with a finest-grid (120 × 120) L2 error of 2.6807 × 10−5 and a fine-grid GCI of 0.013225%. Within the investigated dimensionless range, Nuavg increases with the Rayleigh number, wall-wave amplitude, radiation parameter, and viscosity-thinning magnitude, while the hybrid nanofluid yields a 2.8–3.2% enhancement over pure water. Because no independent experimental measurements or complete dimensional operating envelope are available, the reported engineering implications are presented as model-based guidance rather than validated design prescriptions.