To achieve the long range measurement capability and the accurate resolution in linear laser detection and ranging (LADAR) system, a 32-channel analog front end circuit featured with high gain, high bandwidth, and low noise characteristics is designed. The proposed three-stage analog front end (TS-AFE) includes a variable gain transimpedance amplifier, a differential voltage amplifier, and an analog equalizer. The first stage adopts the shunt-feedback topology to optimize the overall noise, the second stage helps to enlarge the input dynamic range further, and the last stage boosts the channel bandwidth. Furthermore, a 6-bit current digital-to-analog converter (DAC) is integrated in the equalizer to produce a built-in threshold voltage. The 32-channel TS-AFE chip is fabricated with 0.18-μm CMOS technology. The measurement results show that with the highest gain configuration, the circuit realizes 101.6 dB transimpedance gain, 190 MHz bandwidth, and 2.6 pA/sqrt(Hz) input noise current spectral density, respectively. The minimum detectable current achieves 0.4 μA with SNR = 10. The maximum output voltage swing is greater than 1000 mV, and the linear dynamic range reaches 64 dB. The power consumption per channel is as low as 37 mW from a single 3.3 V supply.
A scannerless laser detection and ranging (LADAR) system based on frequency modulation/continuous wave (FM/cw) technique is attractive due to a reduced bandwidth requirement of the receiver circuit. This paper presents the 64×64 TnGaAs-based focal plane array (FPA) self-mixing detectors and the 1×32 element readout integrated circuit (ROTC) array based on transimpedance amplifier for the FM/cw LADAR. Different from conventional detector, the TnGaAs self-mixing detector presents a low impedance and a complex electrical model. The linear chirp local-oscillator (LO) electrical signal through the detector causes a large dc current and a unique dc offset voltage (Vos) error in the ROTC. To overcome these problems, the blocking capacitors and the novel multiple low-pass filters are applied in the ROTC. The ROTC array was fabricated in 0.18-μm CMOS process. The measured results show that the Vos error is eliminated within the limited LO amplitude range and the ROTC achieves a 140-dBΩ transimpedance gain with a bandwidth of 1 MHz. Compared with the state-of-the-art FM/cw LADAR, the ROTC accurately detects the signal of interest of the TnGaAs FPA self-mixing detectors and miniaturizes the LADAR receiver.
As the current mainstream high-precision ADC architecture, sigma-delta ADC is extensively employed in a wide range of domains and applications. This paper presents the design of a highly efficient cascaded digital decimation filter for sigma-delta ADCs, emphasizing the suppression of high folding band noise and the achievement of a flat passband. Additionally, this study addresses the critical balance between filter performance and power consumption. An inserting zero (IZ) filter is incorporated into a cascaded integrator comb (CIC) filter to enhance aliasing suppression. The IZ filter and compensation filter are optimized using the particle swarm optimization (PSO) algorithm to achieve greater noise attenuation and smaller passband ripple. The designed filter achieves a noise attenuation of 93.4 dB in the folding band and exhibits an overall passband ripple of 0.0477 dB within a bandwidth of 20 KHz. To decrease the power consumption in the filter design, polyphase decomposition has been applied. The filter structure is implemented on an FPGA, processing a 5-bit stream from a 64-times oversampling rate and third-order sigma-delta modulator. The signal-to-noise ratio (SNR) of the output signal reaches 91.7 dB. For ASIC design, the filter utilizes 180 nm CMOS technology with a power consumption of 0.217 mW and occupies a layout area of 0.72 mm2. The post-layout simulation result indicates that the SNR remains at 91.7 dB.
16 January 2024 in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
This article presents a low noise and wide linear dynamic 20-channel analog front-end (AFE) array for frequency-modulated continuous-wave (FMCW) light detection and ranging (LiDAR) system. Each channel of the AFE array mainly consists of a shunt feedback transimpedance amplifier (SF-TIA) with a dc cancellation loop (DCL), a post amplifier, and an output buffer. The DCL is proposed to eliminate the dc current, comprising the dc current sunk to ground (dc-STG) and the dc current sourced from power supply (dc-SFP). In addition, the post amplifier, cascaded with an operational transconductance amplifier (OTA) and an SF-TIA, is proposed to decouple the relationship between gain and output common voltage, achieving both large gain and large output swing. Furthermore, the equalization technique is adopted to expand the bandwidth of the AFE array. The AFE array was implemented and fabricated in a 0.18- $\mu $ m CMOS technology. Measurement results show that the AFE array achieves the maximum transimpedance gain of 107 dB and eliminates the dc current between $-$ 150 and 250 $\mu $ A. With the maximum transimpedance gain, the measured bandwidth, the equivalent input-referred rms noise current, and the signal-to-crosstalk ratio (SCR) between adjacent channels are 165 MHz, 29.4 nArms, and $-$ 33.9 dB, respectively. The AFE array also achieves a linear dynamic range (DR) of 66 dB and the area of each channel is approximately equal to 0.16 $\times$ 1.3 mm $^{2}$ .
This article presents a novel readout circuit for the resistive tactile sensor array. Based on the 2-D scanning mechanism, a crosstalk suppression technique is proposed by combining the correlated double sampling (CDS) and zero potential method (ZPM). The output of the same sensor under different bias conditions is captured twice and amplified by a channel-parallel fully differential gain stage, performing analogous subtraction. To achieve nonuniformity compensation, the current injected into the readout channel is adjusted by the channel-parallel digital-to-analog converter (DAC). A successive approximation register (SAR) analog-to-digital converter (ADC) performs quantization, and the chip can be used as a serial peripheral interface (SPI) slave to update register values for gain configuration, power consumption control, and nonuniformity compensation The 180-nm CMOS prototype chip occupies an area of 4.8 $\text{mm}^{2}$ and consumes 285 $\mu$ W. In order to validate the design, a tactile sensing system is built, using the readout circuit along with a 10 $\times$ 10 flexible sensor array. With the techniques proposed in this article, the readout error of the sensors in array is less than 0.3.