Nanocomposites based on bacterial cellulose (BC), hydroxyapatite (HAp), and MXene represent a promising class of biomaterials for regenerative medicine and photothermal technologies due to their combination of biocompatibility, mechanical stability, electrical conductivity, and strong infrared absorption capability. However, the high sensitivity of MXene phases and the cellulose matrix to physicochemical impacts requires careful selection of sterilization approaches that provide sterility without substantial loss of key functional properties. This study presents a comparative evaluation of nine sterilization methods – autoclaving, dry heat, ethylene oxide treatment, γ-irradiation, electron beam (E-beam) irradiation, ultraviolet irradiation, ozonation, supercritical CO₂ treatment, and cold plasma – applied to BC/HAp/MXene nanocomposites. Sterility was assessed by direct plating on nutrient media; sterilization efficiency was calculated based on microbial growth. Complete sterility was achieved for all methods except UV (50%) and CO₂ treatment (90%). The effects of sterilization on material structure and properties were analyzed using SEM imaging, porosity measurement, mechanical testing, electrical conductivity assessment, and photothermal activity evaluation. Thermal treatment and ozonation caused the most pronounced structural damage and reduction in mechanical strength. Radiation-based methods induced moderate changes, whereas ethylene oxide, supercritical CO₂, and cold plasma treatment resulted in minimal morphological degradation. Cold plasma and EtO preserved up to 94–98% of the initial conductivity and photothermal response, while thermal treatment led to significant loss of functional performance due to thermo-oxidative degradation of MXene. Comprehensive analysis demonstrated that cold plasma and ethylene oxide provide the best balance between sterility and preservation of structural–functional properties of BC/HAp/MXene nanocomposites. These methods are the most promising for preparing such materials for biomedical applications.
Структурные особенности бактериальной целлюлозы (БЦ) обеспечивают большую популярность ее использования для создания композитных материалов. Иммобилизация бактерий рода Bacillus в полимере БЦ придает матрице-носителю новые функциональные свойства, способствующие восстановлению и поддержке благоприятного баланса микрофлоры в ЖКТ. Внесение альгината натрия положительно влияло на синтез БЦ K. xylinus C-3, обеспечивая выход полимера – 12,11 г/л. Использован метод «адсорбции-инкубации» для поверхностной и пространственной иммобилизации Bacillus subtilis, обеспечивающий высокую концентрацию клеток – 108 КОЕ на 1 г носителя. Биокомпозит БЦ/Bacillus подавлял рост E. coli, S. typhi, S. typhimurium, Citr. aerogenes, P. vulgaris до 85,4% после 24-часового контакта, а по истечении 72 часов полностью ингибировал рост и жизнеспособность тест-организмов в условиях in vitro. Иммобилизованные пробиотики по уровню резистентности к воздействию желудочного сока значительно превосходили суспензию свободных клеток микроорганизмов. Активность пробиотиков в условиях in vivo определяли на моделях экспериментального дисбактериоза. Пробиотические микрогранулы БЦ/B. subtilis могут быть использованы для коррекции микробиоценоза толстого кишечника.
Bacterial biofilms drive wound chronicity and resist conventional antimicrobial therapies. To address this clinical bottleneck, we engineered a multifunctional, photothermally active sponge-like nanocomposite comprising TEMPO-oxidized bacterial cellulose (TBC), chitosan (CHS), and Ti3C2Tx MXene via in situ modification and cryogenic freeze-drying. Among the formulations evaluated, the TBC/CHS/5%MXene composite exhibited the highest water uptake and the lowest water contact angle, together with improved tensile properties. Upon near-infrared (NIR) irradiation (808 nm, 1.0 W·cm−2), the material rapidly reached 53–55 °C, confirming a pronounced MXene-driven photothermal response. This localized hyperthermia markedly enhanced antibacterial activity against Staphylococcus aureus and Pseudomonas aeruginosa, achieving reductions of 96% and 95%, respectively. Notably, in an ex vivo porcine skin biofilm model, 10 min of NIR irradiation resulted in a 99% reduction in viable bacterial counts, demonstrating pronounced antibiofilm activity. Furthermore, the composite demonstrated intrinsic hemostatic properties, high cytocompatibility, and hemocompatibility. Collectively, these findings support TBC/CHS/5%MXene as an NIR-responsive platform for further investigation of its efficacy and safety in preclinical models of infected wound healing.