In China, more than 10,000 Tailings storage facilities (TSF) have been created on the ground surface through mineral mining processes, these TSF occupy a large amount of land. The strength of the tailings is too low to be able to stand on its own without strengthening. In order to save land resources and alleviate the damage to the environment caused by mineral mining, it is necessary to reinforce the TSF so that they can store more tailings. China is one of the countries with the largest area of permafrost and seasonal frozen regions, accounting for about 75% of the country’s total land area. The problem can be exacerbated in these regions where the freeze–thaw effect can further degrade the strength of tailings. A review of the literature suggests that there is little research on the mechanical and microstructural properties of tailings reinforced with cement-based materials under freeze–thaw conditions, especially when the tailings are to be discharged to land for sustainable development. This study investigates the effect of freeze–thaw cycles on the mechanical properties and microstructural changes of tailings reinforced with cement-based materials to mitigate environmental hazards. Unconfined compressive strength (UCS) tests, scanning electron microscopic images, X-Ray Diffraction tests, thermogravimetry tests and mercury intrusion porosimetry tests were conducted on samples of tailings. The results from this study show that freeze–thaw cycles reduce the UCS of all the tested samples eventually, but the frozen temperature does not significantly affect the UCS. The larger number of freeze–thaw cycles, the more damage is to the surface morphology and the matrix of the tailings. The results presented in the paper can help engineers and managers to effectively transport the TSF to other locations to minimize environmental hazards to achieve sustainable production of mineral mining processes.
Blast furnace slag (BFS) is often used as a cement-based raw material for underground filling and surface cemented paste discharge of tailings during mining processes. This paper studied a new cement-based material (NCM) with BFS to replace ordinary Portland cement (OPC). A uniaxial compressive strength (UCS) experiment was used to test the mechanical strength of samples; X-ray diffraction and thermal gravity experiments were used to test the crystalline phases and amount of hydration products by samples; a scanning electron microscope experiment was used to observe the influence of the hydration products morphology by samples; mercury intrusion porosimetry experiment was used to analyze the pore size distribution of samples. The samples with NCM had an optimum UCS; the crystalline phases of the hydration products were similar in OPC and NCM. However, the amount of product formed in OPC was less than that in NCM at the same curing time; more ettringite and calcium silicate hydrate were produced in samples with NCM, which filled the pores and enhanced the UCS of the samples. The final mercury intrusion volume of the samples with NCM were lower than the samples with OPC at the same curing time, which showed that samples with NCM had lower porosities. For the samples with NCM and OPC cured from 7 days to 28 days, the mercury intrusion volume was reduced by 18% and 13%, and the most common pore size of the samples reduced by 53% and 29%, respectively. This showed after 21 days curing time, the pores of all the samples getting smaller; however, the samples with NCM were more compact. The main ingredients of the NCM were clinker, lime, gypsum and BFS, and its ratio was 14:6:10:70. The content of additives to NCM was 0.4%, and the ratio of sodium sulfate: alum: sodium fluorosilicate was 2:1:1.
With the escalating demand for advanced and eco-friendly processing technologies in mining engineering, the potential applications of microwave heating technology in the treatment of cement tailings backfill (CTB) are expanding significantly. This research comprehensively investigates the mechanisms through which microwave irradiation duration and power influence the mechanical properties of CTB with varying concentrations and cement-to-sand ratios. The aim is to reveal the influencing patterns through experimental methods, providing scientific evidence for optimizing CTB treatment processes. This paper conducted microwave heating tests, uniaxial compression tests, and SEM-EDS tests on CTB. The research results indicate that heating time and power significantly enhance the early strength of CTB, with a more pronounced effect on CTB with higher concentrations and higher cement–sand ratios. When the heating time is 7 min and the heating power is 340 W, the cement hydration reaction is maximally promoted, thereby increasing the density and strength growth rate of CTB. However, excessively long heating time or overly high heating power may cause microcracks or thermal stress concentration within the CTB, adversely affecting the strength growth rate of CTB. Optimal thermal exposure duration and microwave power settings facilitate the activation of cementitious materials and the nucleation of calcium-silicate-hydrate (C-S-H) phases, thereby accelerating the compressive strength evolution of cemented tailings backfill (CTB). The outcomes of this research offer valuable insights into the deployment of microwave heating methodologies in underground mine backfilling, which are pivotal for augmenting the economic viability and environmental sustainability of mining operations.
Prior to being released, the top coal of a fully mechanized caving face typically experiences the effects of mining-induced pressure and disturbances from the hydraulic support’s canopy. To investigate the promoting effect of canopy disturbances in the support-controlled area on the damage of top coal during fully mechanized top-coal caving mining, block instability theory and discrete block numerical simulation methods were employed. The instability modes during the initial support and cyclic disturbance stages were analyzed. The fracture evolution and displacement distribution curves were studied for coal bodies with strengths of 3.1 MPa, 15.0 MPa, and 29.5 MPa under the mining influence and support strengths of 0.5 MPa, 1.0 MPa, and 1.5 MPa during the initial support and cyclic disturbance processes. The results showed that during the initial support stage, the instability of the block-structured coal body exhibited four modes as follows: inter-block breakage, inter-block delamination, intra-block fracture expansion, and inter-block sliding. During the cyclic disturbance stage, the coal body instability showed three modes as follows: inter-block sliding, intra-block fracture expansion, and inter-block rotation. The disturbance from the support had little impact on the fragmentation of both low-strength and high-strength coal bodies. However, small support forces combined with multiple cycles of disturbance had an enhancing effect on the instability of medium-strength block-structured top coal.