Yaojia Ren

Mr. Yaojia Ren


Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
30 June 2025 in Crystals
Verified
Journal Article
Open access
PDF file
Yaojia RenYaojia Ren
Yaojia Ren
JXJiajun Xu
Jiajun Xu
YWYingkang Wei
Yingkang Wei
YLYingying Liu
Yingying Liu
JZJilei Zhu
Jilei Zhu
SLShifeng LIU
Shifeng LIU
Titanium alloys are of significant value in aerospace, biomedical, and marine engineering applications due to their excellent specific strength and favorable biocompatibility. As a crucial interstitial solute, oxygen significantly influences the mechanical properties of titanium alloys. However, excessive oxygen content can lead to severe embrittlement and a significant reduction in ductility. This paper systematically reviews the mechanisms of microstructural evolution induced by oxygen in conventionally manufactured titanium alloys and their impact on mechanical properties, highlighting that conventional processes require complex post-treatments (PT) to achieve a balance between strength and plasticity. This assessment further explores the regulatory mechanisms of oxygen on the microstructure and mechanical properties of laser additive manufactured (LAM) titanium alloys, elucidating the fundamental phenomena regarding the oxygen–microstructure–property relationship. Finally, based on the current research progress, this paper provides an outlook on the future development directions and key research priorities in this field. This review offers valuable insights into the role of oxygen in titanium alloys and the development of high-performance titanium alloys.

19 May 2021 in Coatings
Verified
Journal Article
Open access
PDF file
JHJie Hu
Jie Hu
Yaojia RenYaojia Ren
Yaojia Ren
QHQianli Huang
Qianli Huang
HHHao He
Hao He
Luxin LiangLuxin Liang
Luxin Liang
Hong WuHong Wu
Hong Wu
Ti-23Nb (at.%) coatings on an NiTi alloy with metallurgical bonding were prepared by laser cladding (LC) technology using Ti-Nb mixture powders. The effects of laser processing parameters on the microstructure and mechanical properties of the coatings were systematically investigated and the corrosion resistance of the coatings was assessed. The coatings were composed of TiNb, (Ti, Nb)2Ni, and β-Nb phases. The coatings increased the hardness of the NiTi alloy by a combined strengthening effect of the eutectics and fine microstructure. The corrosion resistance of the coated part was improved. The coatings with great corrosion resistance could keep the coated parts inert in an aggressive environment, and effectively restrain the release of toxic Ni ions, which means that the Ti-Nb alloy coatings are likely to be used as a biomaterial for medical applications.

7 July 2023 in Materials
Verified
Journal Article
Open access
PDF file
JDJingguang Du
Jingguang Du
Yaojia RenYaojia Ren
Yaojia Ren
XLXinyan Liu
Xinyan Liu
FXFeng Xu
Feng Xu
XWXiaoteng Wang
Xiaoteng Wang
Hong WuHong Wu
Hong Wu
Based on the advantage of rapid net-shape fabrication, laser powder bed fusion (LPBF) is utilized to process B4C-reinforced Ti composites. The effect of volumetric energy density (VED) on the relative density, microstructural evolution, tensile properties and wear behaviors of B4C-reinforced Ti composites were systematically investigated. The LPBF-ed samples with high relative density (>99%) can be achieved, while the pores and un-melted powders can be observed in the sample owing to the low energy input (33 J/mm3). The additive particulates B4C were transformed into needle-like TiB whiskers with nano-scale while C dissolved in the Ti matrix. Fine-scale grains (<10 μm) with random crystallographic orientation can be achieved and the residual stress shows a downtrend as the VED increases. Through the analysis of the tensile and wear tests, the sample at 61 J/mm3 VED showed a good combination of strength and wear performance, with an ultimate tensile strength of 951 MPa and a wear rate of 3.91 × 10−4 mm3·N−1m−1. The microstructural evolution in VED changes and the corresponding underlying strengthening mechanisms of LPBF-ed Ti + B4C composites are conducted in detail.

24 October 2025 in Crystals
Verified
Journal Article
Open access
PDF file
YWYingkang Wei
Yingkang Wei
YZYufeng Zhang
Yufeng Zhang
YLYunzhe Li
Yunzhe Li
Yaojia RenYaojia Ren
Yaojia Ren
SZShihao Zhang
Shihao Zhang
SLShifeng LIU
Shifeng LIU
In this study, crack-free M2 high-speed steel (HSS) was successfully fabricated by laser powder bed fusion (L-PBF) using a relatively high substrate preheating temperature of 260 °C. The influence of the resulting microstructure on the hardness and tensile properties along the build direction was thoroughly investigated. The results demonstrate that M2 HSS achieves a relative density of 99.6% when processed with a laser power of 280 W and a scanning speed of 0.8 m s−1. The microstructure predominantly consists of fine martensite, along with retained austenite, lower bainite, and a small quantity of eutectic carbide. With increasing build height (from 0 to 9 mm), the fraction of lower bainite decreases from 32.1 to 13.1%, while the austenite content increases from 0.9 to 29.1%. These microstructural changes lead to a gradual reduction in the material’s strength along the build direction. Specifically, the hardness and tensile strength decrease from 845 HV0.3 and 1520 MPa to 745 HV0.3 and 1251 MPa, respectively. Additionally, the elongation varies between 2.6% and 3.3% across the different build heights.

26 May 2023 in Materials
Verified
Journal Article
Open access
PDF file
Hong WuHong Wu
Hong Wu
Yaojia RenYaojia Ren
Yaojia Ren
YTYingtao Tian
Yingtao Tian
Alberto Orozco CaballeroAlberto Orozco Caballero
Alberto Orozco Caballero
Over the past two decades, laser additive manufacturing technology has evolved rapidly and has been applied in many industrial sectors

15 February 2026 in Materials
Verified
Journal Article
Open access
PDF file
XFXiaodan Fan
Xiaodan Fan
YDYuhua Deng
Yuhua Deng
YWYingkang Wei
Yingkang Wei
Yaojia RenYaojia Ren
Yaojia Ren
SCSitong Chen
Sitong Chen
SLShifeng LIU
Shifeng LIU
H13 tool steel is widely used in the hot work die industry owing to its excellent mechanical properties. However, the inherent anisotropy of its microstructural and mechanical properties during additive manufacturing (AM) via laser powder bed fusion (L-PBF) hinders its broader application. In the current study, Ce-containing and as-built samples were prepared in both vertical and horizontal directions, and their microstructures and tensile properties were investigated. Notably, the grain size of the vertical samples is approximately 2.7 μm, which is 19.2% smaller than that of the horizontal samples in L-PBF H13 steel. In addition, the retained austenite (RA) content in the vertical samples reaches as high as 19.7%, whereas in the horizontal samples, it is only 0.4%. After the addition of Ce, the columnar grains of the building direction (BD) samples transform into equiaxed grains. The RA content of the scanning direction (SD) samples and BD samples is 6.3% and 5.7%, respectively. The tensile test results further demonstrate that Ce-containing BD samples exhibit a tensile strength of 2025.3 MPa and an elongation of 17.3%, with the elongation difference between the two directions being only 0.2%. The addition of Ce reduces microstructural anisotropy, resulting in a significant decrease in the mechanical property anisotropy of the formed parts.