Purpose: The purpose of this study is to highlight the direct fabrication of rapid tooling (RT) with desired mechanical, tribological and thermal properties using fused deposition modelling (FDM) process. Further, the review paper demonstrated development procedure of alternative feedstock filament of low-cost composite material for FDM to extend the range of RT applications. Design/methodology/approach: The alternative materials for FDM and their processing requirements for fabrication in filament form as reported by various researchers have been summarized. The literature demonstrates the role of various post-processing techniques on surface finish of FDM prints. Further, low-cost materials for feedstock filament have been investigated experimentally to check their adaptability/suitability for commercial FDM setup. The approach was to realize the requirements of FDM (melt flow rate, flexibility, stiffness, glass transition temperature and mechanical strength), necessary for the successful run of an alternative filament. The effect of constituents (additives, plasticizers, surfactants and fillers) in polymeric matrix on mechanical, tribological and thermal properties has been investigated. Findings: It is possible to develop composite material feedstock as filament for commercial FDM setup without changing its hardware and software. Surface finish of the parts can further be improved by applying various post-processing techniques. Most of the composite parts have high mechanical strength, hardness, thermal stability, wear resistant and better bond formation than standard material parts. Research limitations/implications: Future research may be focused on improving the surface quality of parts fabricated with composite feedstock, solving issues related to the uniform distribution of filled materials during the fabrication of feedstock filament which in turns further increases mechanical strength, high dimensional stability of composite filament and transferring the technology from laboratory scale to various industrial applications. Practical implications: Potential applications of direct fabrication with RT includes rapid manufacturing (RM) of metal-filled parts and ceramic-filled parts (which have complex shape and cannot be rapidly made by any other manufacturing techniques) in the field of biomedical and dentistry. Originality/value: This new manufacturing methodology is based on the proper selection and processing of various materials and additives to form high-performance, low-cost composite material feedstock filament (which fulfil the necessary requirements of FDM process). Finally, newly developed feedstock filament material has both quantitative and qualitative advantage in RT and RM applications as compared to standard material filament.

Purpose: The purpose of this paper is to review the various pre-processing and post-processing approaches used to ameliorate the surface characteristics of fused deposition modelling (FDM)-based acrylonitrile butadiene styrene (ABS) prototypes. FDM being simple and versatile additive manufacturing technique has a calibre to comply with present need of tailor-made and cost-effective products with low cycle time. But the poor surface finish and dimensional accuracy are the primary hurdles ahead the implementation of FDM for rapid casting and tooling applications.Design/methodology/approach: The consequences and scope of FDM pre-processing and post-processing parameters have been studied independently. The comprehensive study includes dominance, limitations, validity and reach of various techniques embraced to improve surface characteristics of ABS parts. The replicas of hip implant are fabricated by maintaining the optimum pre-processing parameters as reviewed, and a case study has been executed to evaluate the capability of vapour smoothing process to enhance surface finish.Findings: The pre-processing techniques are quite deficient when different geometries are required to be manufactured within limited time and required range of surface finish and accuracy. The post-processing techniques of surface finishing, being effective disturbs the dimensional stability and mechanical strength of parts thus incapacitates them for specific applications. The major challenge for FDM is the development of precise, automatic and controlled mass finishing techniques with low cost and time.Research limitations/implications: The research assessed the feasibility of vapour smoothing technique for surface finishing which can make consistent castings of customized implants at low cost and shorter lead times.Originality/value: The extensive research regarding surface finish and dimensional accuracy of FDM parts has been collected, and inferences made by study have been used to fabricate replicas to further examine advanced finishing technique of vapour smoothing.

This paper highlights the multi-material additive manufacturing (AM) route for manufacturing of innovative materials and structures. Three different recycled thermoplastics, namely acrylonitrile butadiene styrene (ABS), polylactic acid (PLA), and high impact polystyrene (HIPS) (with different Young’s modulus, glass transition temperature, rheological properties), have been selected (as a case study) for multi-material AM. The functional prototypes have been printed on fused deposition modelling (FDM) setup as tensile specimens (as per ASTM D638 type-IV standard) with different combinations of top, middle, and bottom layers (of ABS/PLA/HIPS), at different printing speed and infill percentage density. The specimens were subjected to thermal (glass transition temperature and heat capacity) and mechanical testing (peak load, peak strength, peak elongation, percentage elongation at peak, and Young’s modulus) to ascertain their suitability in load-bearing structures, and the fabrication of functional prototypes of mechanical meta-materials. The results have been supported by photomicrographs to observe the microstructure of the analyzed multi-materials.