In the present work, the state of the art of the most common additive manufacturing (AM) technologies used for the manufacturing of complex shape structures of graphene-based ceramic nanocomposites, ceramic and graphene-based parts is explained. A brief overview of the AM processes for ceramic, which are grouped by the type of feedstock used in each technology, is presented. The main technical factors that affect the quality of the final product were reviewed. The AM processes used for 3D printing of graphene-based materials are described in more detail; moreover, some studies in a wide range of applications related to these AM techniques are cited. Furthermore, different feedstock formulations and their corresponding rheological behavior were explained. Additionally, the most important works about the fabrication of composites using graphene-based ceramic pastes by Direct Ink Writing (DIW) are disclosed in detail and illustrated with representative examples. Various examples of the most relevant approaches for the manufacturing of graphene-based ceramic nanocomposites by DIW are provided.

Alumina toughened zirconia (ATZ) and zirconia toughened alumina (ZTA) are currently the materials of choice to meet the need for tough, strong, and bioinert ceramics for medical devices. However, the mechanical properties of ZrO₂/Al₂O₃dispersion ceramics could be considerably increased by reducing the corresponding grain sizes and by improving the homogeneity of the phase dispersion. Here, we prepare nanoparticles with an intraparticular phase distribution of Zr_(1−x)Al_xO_(2−x/2)and (γ-, δ-)Al₂O₃by the simultaneous gas phase condensation of laser co-vaporized zirconia and alumina raw powders. During subsequent spark plasma sintering the zirconia defect structures and transition alumina phases transform to a homogeneously distributed dispersion of tetragonal ZrO₂(52.4 vol%) and α-Al₂O₃(47.6 vol%). Ceramics sintered by spark plasma sintering are completely dense with average grain sizes in the range around 250 nm. Outstanding mechanical properties (flexural strength σ_f = 1500 MPa, fracture toughnessK_Ic = 6.8 MPa m^1/2) together with a high resistance against low temperature degradation make these materials promising candidates for next generation bioceramics in total hip replacements and for dental implants.

Coatings with a thickness from ~40 to ~50 µm on Ti6Al4V titanium alloys were formed by plasma electrolytic oxidation (PEO) in a silicate-hypophosphite electrolyte with the addition of graphene oxide. The PEO treatment was carried out in the anode–cathode mode (50 Hz) at a ratio of anode and cathode currents of 1:1; their sum density was 20 A/dm², and the treatment’s duration was 30 min. The effect of the graphene oxide’s concentration in the electrolyte on the thickness, roughness, hardness, surface morphology, structure, composition, and tribological characteristics of the PEO coatings was studied. Wear experiments, under dry conditions, were carried out in a ball-on-disk tribotester with an applied load of 5 N, a sliding speed of 0.1 m·s⁻¹, and a sliding distance of 1000 m. According to the obtained results, the addition of graphene oxide (GO) into the base silicate-hypophosphite electrolyte leads to a slight decrease in the coefficient of friction (from 0.73 to 0.69) and a reduction in the wear rate by more than 1.5 times (from 8.04 to 5.2 mm³/N·m), with an increase in the GO’s concentration from 0 to 0.5 kg/m³, respectively. This occurs due to the formation of a GO-containing lubricating tribolayer upon contact with the coating of the counter-body in the friction pair. Delamination of the coatings during wear occurs due to contact fatigue; with an increase in the concentration of GO in the electrolyte from 0 to 0.5 kg/m³, this process slows down by more than four times.

In this study the influence of TiC content on the mechanical and electrical properties of Al₂O₃-TiC composites containing 30 and 40 vol.% TiC were investigated. The Vickers hardness and fracture toughness of the composites increased with the addition of TiC phase. The composite with 40 vol.% TiC showed the highest flexural strength (687 ± 39 MPa), fracture toughness (7.8 ± 0.4 MPa·m^1/2) and hardness (22.3 ± 0.3 GPa) with a homogeneous distribution of the second phase within the ceramic matrix. Besides enhanced mechanical properties, it was found that ceramic composites with more than 30 vol.% TiC fabricated by the spark plasma sintering possess sufficient electrical conductivity for electrical discharge machining as well. Therefore, they do not limit the flexibility of the shape, and any intricate parts can be easily made with these composites which can be recommended for the production of cutting inserts in the tools for machining of superhard hardened steels, hard-to-machine materials, composites and other materials used in mechanical engineering.