Accurate estimation of lithium battery state of charge is very important for ensuring the operation of battery management system, realizing the energy management strategy of electric vehicles, reducing mileage anxiety and promoting the sustainable development of electric vehicles. In this paper, several studies are carried out for state of charge estimation of lithium-ion battery: (1) Aiming at the problem of parameter identification of battery model, an optimal identification method of model parameters based on ant lion optimization algorithm is proposed. (2) An adaptive weighting Cubature particle filter (AWCPF) method is proposed for SOC estimation. The proposed AWCPF method is based on particle filter (PF) algorithm, while the Cubature Kalman filter (CKF) algorithm is utilized to generate the proposal distribution for PF algorithm, which can retrain the particles degradation problem in PF algorithm. To solve the problem that the CKF algorithm is sensitive to noise, comparing with fixed sigma point weights of the conventional CKF, the weights of sigma points are adaptively adjusted based on state and measurement residual vectors. Furthermore, the process noise and measurement noise are estimated iterative. In this paper, experimental verification of different initial values of SOC under various working conditions is carried out. The results show that the proposed AWCPF algorithm based SOC estimation method has high estimation accuracy, strong robustness, fast convergence speed, with the maximum SOC estimation error is less than 1%.

An accurate estimation of the state of health (SOH) of Li-ion batteries is critical for the efficient and safe operation of battery-powered systems. Traditional methods for SOH estimation, such as Coulomb counting, often struggle with sensitivity to measurement noise and time-consuming tests. This study addresses this issue by combining incremental capacity (IC) analysis and a novel neural network, Kolmogorov–Arnold Networks (KANs). Fifteen features were extracted from IC curves and a 2RC equivalent circuit model was used to identify the internal resistance of batteries. Recursive least squares were used to identify the parameters of the equivalent circuit model. IC features and internal resistance were considered as input variables to establish the SOH estimation model. Three commonly used machine learning methods (BP, LSTM, TCN) and two hybrid algorithms (LSTM-KAN and TCN-KAN) were used to establish the SOH estimation model. The performance of the five models was compared and analyzed. The results demonstrated that the hybrid models integrated with the KAN performed better than the conventional models, and the LSTM-KAN model had higher estimation accuracy than that of the other models. The model achieved a mean absolute error of less than 0.412% in SOH prediction in the test and validation dataset. The proposed model does not require complete charge and discharge data, which provides a promising tool for the accurate monitoring and fast detection of battery SOH.

Permanent magnet synchronous motors (PMSMs) are extensively utilized in production and manufacturing fields due to their wide speed range, high output torque, fast speed response, small size and light weight. PMSMs are susceptible to inter-turn short circuit faults, demagnetization faults, bearing faults, and other faults arising from irregular vibrations and frequent start–brake cycles. While fault diagnosis for PMSMs offers an effective means to enhance operational efficiency, the multi-sensor information fusion is often overlooked. In industrial production processes, the collected data inevitably suffers from noise contamination, which can adversely impact diagnostic outcomes. To enhance the robustness of diagnostic methods in noisy environments and mitigate the risk of overfitting, a PMSM fault diagnosis method based on image features of multi-sensor fusion is proposed. Firstly, the vibration acceleration signals of the PMSM at different positions were acquired. Then, the newly designed multi-signal Gramian Angular Difference Fields (MGADF) method combines sensor signals from three different installation locations into a single image. Next, the multi-texture features are fused to extract the features of the image. Various machine models are compared in the fault feature learning and classification, and the results show that the proposed diagnostic method has good diagnostic accuracy and robustness, with an average diagnostic accuracy of 99.54% and a standard deviation of accuracy of 0.19. It has excellent performance even in noisy environments. The method is non-invasive and can be extended and applied to the condition monitoring and diagnosis of industrial motors.

Accurate estimation of vehicle states is extremely crucial for vehicle stability control. As a reliable estimation methodology, the unscented Kalman filter (UKF) has been widely utilized in vehicle control. However, the estimation accuracy still needs to be improved caused by the unpredictable measurement and process noise. In this paper, a novel modified UKF state estimation methodology combined with the ant lion optimization (ALO) is proposed for the stability control of a four in-wheel motor independent drive electric vehicle (4WIDEV). First, the optimal performance of the ALO algorithm is analyzed, where both unimodal and multimodal optimization test functions are selected and optimized by GA, PSO, and ALO, respectively. The results indicate that the ALO algorithm has good global optimization capability and applicability. Second, the ALO algorithm is merged into the UKF to adjust the statistical properties of noise information for the ALOUKF estimator design without extra sensor signals. At last, the simulations on the Matlab/Simulink-CarSim co-simulation platform and the road test based on an A&D 5435 rapid prototyping experiment platform (RPP) are carried out to verify the proposed method. The simulation and experiment results demonstrate that the ALOUKF estimator can improve state estimation accuracy and resist the vehicle nonlinearity even in the case of the complicated and emergency maneuvers.

The aim of this paper is to solve the problem for battery electric vehicles of low-precision and time-consuming inspection. A novel method of driving cycle development for battery electric vehicles’ operational safety is proposed in this paper. First, three inspection items are proposed based on relevant testing standards. The inspection calculation method of operational safety is developed based on the acceleration changing rate. Then the multi-cycle inspection method with the stable pedal mode is developed, and the Gauss filtering algorithm is applied for data preprocessing. A rapid inspection driving cycle construction method based on support vector machine is proposed, and a driving cycle is built with a total time of 204 s by fusing and splicing kinematic fragments. Finally, the proposed inspection calculation method is used to validate the operational safety inspection items by tracking the established rapid inspection driving cycle based on the test bench. The results shown are those that qualified the range of acceleration changing rate for driving stability [−0.35, −0.04]. The range for gliding smoothness is [0.05, 0.09]. The range for braking coordination is [−0.04, 0.095]. The maximum RMSE between the constructed rapid inspection segments is 9%, and the maximum RMSE between the tested driving segments is 6%. Test results meet design requirements. The thresholds for operational safety inspection items are evaluated based on the test results. We set less than 0.5 as the safety threshold for driving stability. During the experiment, gliding was less than 0.1 as the safety threshold for gliding comfort, and during braking it was less than 0.1 as the safety threshold for vehicle braking coordination.