Catalysts based on CuAl-, CoAl-, and CuCoAl-layered hydroxides with M2+/Al = 2 and Cu/Co = 1 molar ratio were obtained. The effect of amount of cobalt on the structural properties, morphology, surface cations distribution, oxide phase formation, thermal stability of the samples and reduction of metals from them was studied. The effect of reaction conditions (temperature, time, pressure, solvent) and conditions of preliminary treatment of catalysts on their catalytic properties in furfural hydrogenation was established. High selectivity to furfuryl alcohol was observed for all the samples irrespective of pretreatment and reaction conditions. The synergetic effect in furfural hydrogenation between Co and Cu in the CuCoAlOx catalysts was revealed when ethanol is used as a solvent.
The paper presents that the graphite mechanical activation (MA) results in the particles size reduction and crystal structure disorder. The estimation of the electric conductivity of high-dispersive graphite powders was performed and the specific electric resistance improving is represented to occur after MA by two orders at the grinding bodies acceleration (1000 m/s2). Thus MA cannot be used for the particles size reduction, the electric resistance value being kept at the initial graphite level in the intensive conditions. The electric resistance of the samples improves from 2 to 6 times after MA at the low grinding bodies acceleration (300 m/s2) therefore MA in the “mild conditions” is more perspective approach to the conductive carbon powders development with the preset particles size
The applications of catalysts based on molybdenum carbide are considered. Attention is focused on the effects of molybdenum carbide preparation methods on
Procedures for the synthesis of massive molybdenum carbide by the mechanical activation of a mixture of MoO3, commercial carbon, and Zn in air and the synthesis of the supported carbide-containing catalyst Mo2C/C by the mechanical activation of commercial carbon impregnated with a 16% aqueous solution of ammonium paramolybdate in an inert atmosphere were developed for the first time. With the use of a set of physicochemical methods, the metal contents, particle sizes, specific surface areas, and phase compositions of the mechanically activated composites were determined. The structure of the carbide-containing supported catalyst was studied by electron microscopy, and its acidic properties were studied by the temperature-programmed desorption of ammonia; catalytic tests in the model reactions of dibenzothiophene (DBT) and alkane aromatization were performed. It was found that the Mo2C/C catalyst exhibited high activity in these reactions: the conversion of DBT at a contact time of 3–6 h was 80–85%. The conversion of n-heptane at a contact time of 2 h was 31.2%, and 100% toluene was the reaction product. An increase in the contact time to 6 h led to a decrease in the conversion of n-heptane to 1.3%, and to 47% C6-C7 cycloalkanes were present in the reaction products. The results of this work are indicative of the high catalytic activity of the Mo2C/C catalyst obtained by mechanical activation.
Single phase CuCoMgAl-layered hydroxides were obtained by making fine adjustment to their composition through changing the (Co + Cu)/Mg = 0.5; 1; 2; 3 and Co/Cu = 0.5; 1; 2 ratios. The rise of Co/Cu in systems contributed to the increase in their thermal stability. CuCoMgAl-catalysts showed high selectivity of carbonyl group hydrogenation in furfural and 5-hydroxymethylfurfural. In furfural hydrogenation, the selectivity to furfuryl alcohol was more than 99%, and in 5-hydroxymethylfurfural hydrogenation, the selectivity to 2,5-hydroxymethyl furfural was 95%. The surface of the samples with different Co/Cu after calcination and reduction was the same and had a «core-shell» structure (TEM). «Core» consisted of Cu and Co metallic particles. «Shell» consisted of CuCoMgAlOx mixed no-stoichiometric spinel oxides. There was no sintering or change in size of the metallic particles after the reaction. For the sample with Co/Cu = 1, their phase composition after reaction remained unchangeable. The increase of Co/Cu led to the formation of an X-ray amorphous phase after the reaction. This suggests the decrease in structural stability of this sample. The obtained results prove the prospects of using bimetallic CoCu-systems for hydrogenation of furan aldehydes, and opens up new directions for further research and improvement.