Multipath transport protocols utilize multiple network paths (e.g., WiFi and cellular) to achieve improved performance and reliability, compared with their single-path counterparts. The scheduler of a multipath transport protocol determines how to distribute the data packets onto different paths. However, state-of-the-art multipath schedulers face the challenge when dealing with heterogeneous paths with dynamic path characteristics (i.e., packet loss, fluctuation of delay). In this paper, we propose Peekaboo, a novel learning-based multipath scheduler that is aware of the dynamic characteristics of the heterogeneous paths. Peekaboo is able to learn scheduling decisions to adopt over time based on the current path characteristics and dynamicity levels -from both deterministic and stochastic perspectives. We implement Peekaboo in Multipath QUIC (MPQUIC) and compare it with state-of-the-art multipath schedulers for a wide range of dynamic heterogeneous environments, upon both emulated and real networks. Our results show that Peekaboo outperforms the other schedulers by up to 31.2% in emulated networks and up to 36.3% in real network scenarios.

Widespread adoption of indoor positioning systems based on WiFi fingerprinting is at present hindered by the large efforts required for measurements collection during the offline phase. Two approaches were recently proposed to address such issue: crowdsourcing and RSS radiomap prediction, based on either interpolation or propagation channel model fitting from a small set of measurements. RSS prediction promises better positioning accuracy when compared to crowdsourcing, but no systematic analysis of the impact of system parameters on positioning accuracy is available. This paper fills this gap by introducing ViFi, an indoor positioning system that relies on RSS prediction based on Multi-Wall Multi-Floor (MWMF) propagation model to generate a discrete RSS radiomap (virtual fingerprints). Extensive experimental results, obtained in multiple independent testbeds, show that ViFi outperforms virtual fingerprinting systems adopting simpler propagation models in terms of accuracy, and allows a sevenfold reduction in the number of measurements to be collected, while achieving the same accuracy of a traditional fingerprinting system deployed in the same environment. Finally, a set of guidelines for the implementation of ViFi in a generic environment, that saves the effort of collecting additional measurements for system testing and fine tuning, is proposed.

In the last years, the Internet of Things (IoT) has emerged as a key application context in the design and evolution of technologies in the transition toward a 5G ecosystem. More and more IoT technologies have entered the market and represent important enablers in the deployment of networks of interconnected devices. As network and spatial device densities grow, energy efficiency and consumption are becoming an important aspect in analyzing the performance and suitability of different technologies. In this framework, this survey presents an extensive review of IoT technologies, including both Low-Power Short-Area Networks (LPSANs) and Low-Power Wide-Area Networks (LPWANs), from the perspective of energy efficiency and power consumption. Existing consumption models and energy efficiency mechanisms are categorized, analyzed and discussed, in order to highlight the main trends proposed in literature and standards toward achieving energy-efficient IoT networks. Current limitations and open challenges are also discussed, aiming at highlighting new possible research directions.

Although Starlink has been rolled-out for several years, there is still a lack of knowledge regarding system details and performance characteristics. To address this, we perform a network layer measurement campaign utilizing precise times-tamping to analyze throughput variations at multiple time scales, and infer system timing details. On larger timescales we quantify the diurnal variations where the throughput varies with the time of day. On the medium timescales we establish the likely frequency allocation and beam switching period to be 15 seconds. The associated connectivity disturbances contribute to severe link underutilization for single long-lived TCP flows, which typically reach only 46% of the estimated link capacity. On the sub-millisecond timescale our network layer measurements corroborate recent physical layer investigations of the Starlink frame timing, which is confirmed to be 1.33 ms.

The fifth generation (5G) cellular network aims at providing very high data rates, ultra reliable low latency communications, and a vast increase of connection density. As one of the design trends towards these objectives, 5G exploits multi-connectivity, i.e., the concurrent use of multiple access networks. The Access Traffic Steering, Switching, and Splitting (ATSSS) architecture has recently been proposed to enable 5G multi-connectivity, and multipath transport protocols have emerged as a key ATSSS technology enabler. Within this context, this survey presents a detailed review of multipath transport protocols, identifies their existing and potential exploitation in ATSSS, and suggests their applicability for enhanced Mobile Broadband (eMBB) and Ultra Reliable Low Latency Communications (URLLC) services. To this end, we first review 5G background and current standardization activities around multi-connectivity and the ATSSS architecture. We then provide an in-depth review of multipath transport protocols, covering four core functionalities, i.e., path management, scheduling, congestion control, and reliable transfer. Based on the reviewed literature, we further discuss the integration of multipath transport into ATSSS to achieve eMBB and URLLC service requirements. Finally, we also point out major open research issues and discuss possible future directions.

The weighted k-nearest neighbors (WkNN) algorithm is by far the most popular choice in the design of fingerprinting indoor positioning systems based on WiFi received signal strength (RSS). WkNN estimates the position of a target device by selecting k reference points (RPs) based on the similarity of their fingerprints with the measured RSS values. The position of the target device is then obtained as a weighted sum of the positions of the k RPs. Two-step WkNN positioning algorithms were recently proposed, in which RPs are divided into clusters using the affinity propagation clustering algorithm, and one representative for each cluster is selected. Only cluster representatives are then considered during the position estimation, leading to a significant computational complexity reduction compared to traditional, flat WkNN. Flat and two-step WkNN share the issue of properly selecting the similarity metric so as to guarantee good positioning accuracy: in two-step WkNN, in particular, the metric impacts three different steps in the position estimation, that is cluster formation, cluster selection and RP selection and weighting. So far, however, the only similarity metric considered in the literature was the one proposed in the original formulation of the affinity propagation algorithm. This paper fills this gap by comparing different metrics and, based on this comparison, proposes a novel mixed approach in which different metrics are adopted in the different steps of the position estimation procedure. The analysis is supported by an extensive experimental campaign carried out in a multi-floor 3D indoor positioning testbed. The impact of similarity metrics and their combinations on the structure and size of the resulting clusters, 3D positioning accuracy and computational complexity are investigated. Results show that the adoption of metrics different from the one proposed in the original affinity propagation algorithm and, in particular, the combination of different metrics can significantly improve the positioning accuracy while preserving the efficiency in computational complexity typical of two-step algorithms.