7 May 2018 in Applied Physics Letters
Using a tiered deposition approach, Hf1-xZrxO2 (HZO) films with varying atomic layer deposition (ALD) cycles from 36 to 52 cycles were grown on Ge, Ir, and TiN substrates in single runs and annealed at 500 °C. 40 ALD cycle films grown on Ir exhibit a switched polarization (Psw) of 13 μC/cm2, while those grown on Ge and TiN did not exhibit measurable Psw values until 44 and 52 ALD cycles, respectively. High-resolution cross-sectional transmission electron microscopy confirmed these results; the ferroelectric films are crystalline with defined lattice fringes, while non-ferroelectric films remain amorphous. 52 ALD cycle 1:1 HZO grown on Ge had the highest Psw of all the films fabricated at 39 μC/cm2, while the 1:1 HZO grown on TiN displayed continuous wake-up and no fatigue up to 1010 cycles with the Psw increasing from <1 μC/cm2 to 21 μC/cm2.
21 January 2020 in Applied Physics Letters
The emerging field of ferroelectric hafnium zirconium oxide has garnered increased attention recently for its wide array of applications from nonvolatile memory and transistor devices to nanoelectromechanical transducers. Atomic layer deposition is one of the preferred techniques for the fabrication of hafnium zirconium oxide thin films, with a standard choice of oxidizer being either O3 or H2O. In this study, we explore various oxidizing conditions and report on the in situ treatment of hydrogen plasma after every atomic layer during the deposition of hafnium zirconium oxide to increase the virgin state polarization. Three different oxidization methods were utilized during the fabrication of the Hf0.5Zr0.5O2 films: H2O, O2 plasma, and O2 plasma followed by H2 plasma. The 10 and 8 nm thick films oxidized with only O2 plasma result in initially anti-ferroelectric films. Comparatively, the addition of H2 plasma after every O2 plasma step results in films with strong ferroelectric behavior. Peak shifting of the GIXRD pattern suggests that the sequential O2-H2 plasma films tend more to the orthorhombic phase as compared to the O2 plasma and H2O oxidized films.
27 January 2020 in Applied Physics Letters
This paper reports a 30 nm-thick integrated nano-electro-mechanical resonator based on atomically engineered ferroelectric hafnium zirconium oxide (Hf0.5Zr0.5O2) film. A 10 nm-thick Hf0.5Zr0.5O2 layer is atomically engineered through capping with 10 nm-thick titanium nitride (TiN) layer and rapid thermal annealing to promote the orthorhombic crystal phase with strong ferroelectric properties. The resulting metal-ferroelectric-metal (MFM) membrane is then patterned to create an integrated nano-electro-mechanical resonator with an overall thickness of 30 nm and a planar-to-vertical aspect ratio exceeding 104:1. Benefiting from large electrostrictive effects in ferroelectric Hf0.5Zr0.5O2, the 30 nm-thick nanomechanical resonator is excited into flexural resonance at 195 kHz with a very large vibration amplitude of ∼100 nm. The transmission response of the nano-electro-mechanical resonator is extracted, using a two-port apodization of the TiN electrodes, showing quality factors (Q) of 15 and 3300 at atmospheric and 10−7 Torr ambient pressures, respectively. Finally, the structural robustness of the MFM nano-membrane is explored through the application of a ∼24 μm deflection, using a point-force by a micro-probe, highlighting the extended elasticity despite the small thickness and ultra-high aspect ratio. The atomic-level thickness, fully integrated operation, high Q, and structural robustness of the Hf0.5Zr0.5O2-based nano-membrane resonator promise its potential for the realization of highly integrated transducers for chip-scale classical and quantum information processing and sensing applications.
27 March 2019 in Thin Solid Films
22 March 2019 in IEEE Electron Device Letters
This letter reports a non-reciprocal filter based on the use of nonlinearities in high quality-factor (Q) silicon microacoustic resonators with asymmetric piezoelectric transducers. The two-port resonators are created by integration of 120nm piezoelectric aluminum nitride and 10nm ferroelectric hafniumzirconium-oxide transducers atop of 70nm single crystal silicon. The asymmetric electromechanical transduction architecture results in highly contrasted power-handing of the micro-acoustic resonator when excited at different ports, resulting in nonreciprocal transmission response for excitation powers beyond a certain threshold. A proof-of-concept filter at 253MHz with 0.25%-3dB-bandwidth is implemented through electrical coupling of two asymmetrically transduced resonators with individual Q of ~870. The filter demonstrates a non-reciprocal transmission ratio of ~16dB for input power exceeding 5dBm.
7 September 2021 in Journal of Applied Physics
Imprint, the preferential orientation of the polarization of a ferroelectric device subjected to elevated temperatures, is a primary reliability concern afflicting data retention in ferroelectric RAM. In this paper, we demonstrate Preisach-based hysteresis modeling, which can be used to predict imprint behavior in ferroelectric thin films. A method was developed for capturing imprint in the context of a Preisach model and a numerical approach for evaluating the Preisach distribution was expanded upon. Interpolation and curve fitting were used to make predictions of the Preisach distributions of imprinted ferroelectric hafnium zirconium oxide devices after short-duration bakes at 23–260 °C and long-term bakes at 85 and 125 °C. In the case of long-term bakes, imprint-induced coercive shifts were modeled as shifts in the derivative of the top and bottom hysteretic polarization curves. The shift in the curves is modeled by fitting experimental data to a commonly used empirically logarithmic relationship reported in the literature. Simulations give remanent polarizations and coercive fields within <5.0 μC/cm2 and 0.1 V, respectively, of the raw data average.