Successful geological sequestration of carbon depends strongly on reservoir seal integrity and storage capacity, including CO2 injection efficiency. Formation of solid hydrates in the near-wellbore area during CO2 injection can cause permeability impairment and, eventually, injectivity loss. In this study, flow remediation in hydrate-plugged sandstone was assessed as function of hydrate morphology and saturation. CO2 and CH4 hydrates formed consistently at elevated pressures and low temperatures, reflecting gas-invaded zones containing residual brine near the injection well. Flow remediation by methanol injection benefited from miscibility with water; the methanol solution contacted and dissociated CO2 hydrates via liquid water channels. Injection of N2 gas did not result in flow remediation of non-porous CO2 and CH4 hydrates, likely due to insufficient gas permeability. In contrast, N2 as a thermodynamic inhibitor dissociated porous CH4 hydrates at lower hydrate saturations (<0.48 frac.). Core-scale thermal stimulation proved to be the most efficient remediation method for near-zero permeability conditions. However, once thermal stimulation ended and pure CO2 injection recommenced at hydrate-forming conditions, secondary hydrate formation occurred aggressively due to the memory effect. Field-specific remediation methods must be included in the well design to avoid key operational challenges during carbon injection and storage.
The interest and on-going research on utilisation of lignin as feedstock for production of renewable and sustainable aromatics is expanding and shows great potential. This study investigates the applicability of semi-continuously organosolv extracted lignin in Lignin-to-Liquid (LtL) solvolysis, using formic acid as hydrogen donor and water as solvent under high temperature–high pressure (HTHP) conditions. The high purity of the organosolv lignin provides high conversion yields at up to 94% based on lignin mass input. The formic acid input is a dominating parameter in lignin conversion. Carbon balance calculations of LtL-solvolysis experiments also indicate that formic acid can give a net carbon contribution to the bio-oils, in addition to its property as hydrogenation agent. Compound specific quantification of the ten most abundant components in the LtL-oils describe up to 10% of the bio-oil composition, and reaction temperature is shown to be the dominating parameter for the structures present. The structural and quantitative results from this study identify components of considerable value in the LtL-oil, and support the position of this oil as a potentially important source of building blocks for the chemical and pharmaceutical industry.
In recent years, hydrothermal liquefaction (HTL) has gained attention as a means of enhancing and increasing the production of biofuels from biomass. Co-HTL involves the simultaneous processing of two or more feedstocks, with the potential for interactions that can affect the overall yield and quality of the resulting biofuels. This study investigates the bio-crude yield, chemical composition, and energy content of bio-crudes obtained through formic acid-assisted hydrothermal liquefaction of combined digested sewage sludge (DSS) and lignocellulose (LC). The bio-crude yields are in the range of 26.8–58.9 wt%, with a higher heating value (HHV) of approximately 32 MJ/kg. The best experiment shows that mixtures with more DSS and high levels of process condition variables (350 °C, formic acid present, and 50 wt% EtOH) give high bio-crude yields with a maximum value of 58.9 wt%. For comparison, pure DSS and LC run at these process conditions resulted in a bio-crude yield of 52.5 wt% and 48.3 wt%, respectively. Partial least squares (PLS) regression reveals a synergistic effect from mixing the feedstocks, as the quadratic term of the regression equation for mixture ratio shows a negative coefficient. GC–MS data show that combining feedstocks results in the formation of new compounds, mostly phenols, that are not present in the bio-crudes from the separate feedstocks. Thus, combining feedstocks will not only increase the resource availability for hydrothermal liquefaction and streamline the process but will also increase the overall production of bio-crude with its synergistic effect.
This work evaluates the effect of feedstock type and composition on the conversion of lignin to liquid by solvolysis with formic acid as hydrogen donor (LtL), by analyzing the yields and molecular composition of the liquid products and interpreting them in terms of both the type and the preprocessing of the lignocellulosic biomass using chemometric data analysis. Lignin samples of different types and purities from softwood, hardwood, and grasses (rice straw and corn stover) have been converted to bio-oil, and the molecular composition analyzed and quantified using GC-MS. LtL solvolysis was found to be a robust method for lignin conversion in terms of converting all samples into bio-oils rich in phenolic compounds regardless of the purity of the lignin sample. The bio-oil yields ranged from 24–94 wt.% relative to lignin input and could be modelled well as a function of the elemental composition of the feedstock. On a molecular basis, the softwood-derived bio-oil contained the most guaiacol-derivatives, and syringol was correlated to hardwood. However, the connection between compounds in the bio-oil and lignin origin was less pronounced than the effects of the methods for biomass fractionation, showing that the pretreatment of the biomass dominates both the yield and molecular composition of the bio-oil and must be addressed as a primary concern when utilization of lignin in a biorefinery is planned.
This paper aims at assessing the impact of retrofitting an existing, 730 MW, coal-fired power plant into a biomass-fired combined heat and power (CHP) plant on its energetic and exergetic performances. A comprehensive thermodynamic model of the power plant was developed and validated against field data, resulting in less than deviation between the model and the measurements for the main process parameters. The validated model was then used to predict the behaviour of the biomass CHP after retrofitting. The modelled CHP unit is coupled to a steam-explosion biomass upgrading plant, a biorefinery process, and a high-temperature heat network. 13 scenarios were studied. At constant boiler load, delivering heat to the considered heat clients can increase the total energy efficiency of the plant from (electricity only) to , while the total exergy efficiency decreases from to . A total energy efficiency of could be reached by lowering the network temperature from C to C. Identifying the needed heat clients could, however, represent a limiting factor to reach such high efficiencies. For a constant power demand, increasing the boiler load from 80 to in order to provide additional heat makes the total energy efficiency increase from to , while the total exergy efficiency decreases from to .