Sigma–delta ( $\Sigma \Delta$ ) digital-to-analog converters (DACs) are commonly used to realize programmable dc voltage generators in built-in self-test (BIST) schemes, largely on account of their high linearity. Unfortunately, such $\Sigma \Delta $ -DACs require large amounts of digital memory and a reconstruction filter with a large silicon area footprint. In this article, a segmented DAC architecture is proposed. The proposed architecture is realized using two sub-DACs, where both are $\Sigma \Delta $ -based. This DAC provides two advantages: filter footprint size reduction and memory savings, thereby allowing for a simpler BIST solution. The benefits of using the segmented $\Sigma \Delta $ -DAC are shown using two experimental prototypes. The first is an IC prototype design using the TSMC 65-nm CMOS technology. It will be shown that the IC achieves 12 bits of resolution from 1020 memory elements, whereas an unsegmented $\Sigma \Delta $ -DAC uses 4095 elements to obtain the same resolution. This is about a 75% savings in memory elements. The segmented prototype occupies 0.5 mm 2 of silicon area, whereas the unsegmented design occupies 0.77 mm 2 for the same resolution. A 35% silicon area savings compared with its unsegmented counterpart. A second prototype implements the segmented $\Sigma \Delta $ -DAC architecture using discrete components. The discrete prototype achieves 16 bits of resolution from 1020 memory elements, whereas the unsegmented counterpart uses 65 535 bits for the same resolution. This is a 98% saving in memory elements.
4 November 2021 in IEEE Transactions on Circuits and Systems II: Express Briefs
This brief presents a fully integrated energy-efficient memory-based direct digital frequency synthesizer (DDFS). To overcome the limitation of using an accumulator and a Read-Only Memory (ROM) Lookup Table (LUT) within a DDFS, the proposed design utilizes a 6-bit memory with a configured mode of operation to synchronize the digital output clock with the input sampling clock. The proposed DDFS is able to tune the output phase and frequency once a phase rotator is used in the input clock path. To realize the proposed DDFS, a 6-bit memory in front-end and some analog blocks in back-end are employed. The prototype DDFS achieves jitter below 12.7ps $_{rms}$ integrated over a 100MHz bandwidth with 28.25Hz resolution while consuming less than 3mW at sampling clock 3.12GHz. The proposed DDFS is fabricated in a 0.9V TSMC 7nm CMOS process and occupies a core area of only 0.014mm 2 .
11 March 2024 in IEEE Transactions on Instrumentation and Measurement
This paper proposes an adaptive all-digital background compensation of timing skew mismatches in time-interleaved analog-to-digital converters (TI-ADCs). The proposed approach uses the orthogonality between the desired component representing ideal samples of the TI-ADC input signal and the timing skew mismatch errors. Our technique is the first attempt to use a source separation mechanism to recover the desired component in the digital output of TI-ADC. A finite impulse response (FIR) filter implementing the Hilbert transform and two separate adaptive FIR (A-FIR) filters are exploited to implement this recovery process. The proposed technique works at frequencies close to the full admissible Nyquist frequency range, and its operation does not depend on the number of sub-ADCs (SADCs). This method operates without any extra SADC. The main cost introduced by the proposed compensation technique is the requirement of two adjustable FIR filters. This cost is proportional to the number of taps in these FIR filters that can be optimized according to the specific application. This technique is validated through various behavioral simulations and a field-programmable-gate-array (FPGA) implementation. With the proposed method, the signal-to-noise and distortion ratio (SNDR) is enhanced from 23.06 dB to more than 66.82 dB in a 12-bit TI-ADC when the standard deviation of timing skew mismatches is 10% of the TI-ADC’s sampling interval.
1 October 2006 in 2006 IEEE International Test Conference
A robust programmable analog Gaussian noise generator suitable for mixed-signal/digital ATEs is presented. Unlike conventional methods (LFSR based noise generators or resistor thermal noise amplification techniques), the user has full control of the characteristics of the Gaussian signal. Indeed, the frequency band, the mean, and variance of the distribution are fully programmable over the voltage range within the supply rails. The method consists of digitally encoding the specified Gaussian signal in a RAM, using pulse-density modulation, followed by filtering the bit stream using an analog low-pass filter. It is demonstrated that the quality of the generated noise signal is independent of the quality of the filter used; hence, making the noise source highly robust. The output of the noise generator accurately models a real Gaussian signal, even at high sigma values; thus, making it a very effective and predictable dithering signal. Two applications of the proposed Gaussian noise source are demonstrated: ADC histogram testing and high-resolution digitization
Seizures due to Hippocampal origins are very common amongst epileptic patients. This article presents a novel seizure prediction approach based on graph theory. The early identification of seizure signature allows for various preventive measures to be undertaken. The proposed approach consists of observing a high correlation level between any pair of electrodes along with voltage peaks in the Delta frequencies. Statistical analysis tools were used to determine threshold levels for this frequency sub-band. A graph topology involving IEEG electrodes characterizes seizure signatures for each patient. In order to validate the proposed approach, six patients from both sexes and various age groups with temporal epilepsies originating from the hippocampal area were studied. An average seizure prediction of 30 minutes, a detection accuracy of 72%, and a false positive rate of 0% were accomplished throughout 200 hours of recording time.
In this paper, we propose a novel circuit and system to optimize the spacing between optical channels in gridless (also called flexible-grid or elastic) networking. The method will exploit the beginning-of-life link margin by enabling the channel to operate in super-Nyquist dense wavelength division multiplexing mode. We present the work in the context of software-defined networking and high-speed optical flexible-rate transponders. The clock recovery scheme allows the mitigation of jitter by decoupling the contribution of high-jitter noise sources from the clock recovery loop. The method and associated algorithm are experimentally verified where a spectrum gain of up to 2 GHz in spacing between two channels in the Media Channel (MC) is obtained compared to conventional clocking strategies. We showed that the improvement is equivalent to increasing throughput, in a data-center interconnect scenario, by up to 300 giga-bits per second per route.