31 August 2021 in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
Sigma–delta ( $\Sigma \Delta$ ) digital-to-analog converters (DACs) are commonly used to realize programmable dc voltage generators in built-in self-test (BIST) schemes, largely on account of their high linearity. Unfortunately, such $\Sigma \Delta $ -DACs require large amounts of digital memory and a reconstruction filter with a large silicon area footprint. In this article, a segmented DAC architecture is proposed. The proposed architecture is realized using two sub-DACs, where both are $\Sigma \Delta $ -based. This DAC provides two advantages: filter footprint size reduction and memory savings, thereby allowing for a simpler BIST solution. The benefits of using the segmented $\Sigma \Delta $ -DAC are shown using two experimental prototypes. The first is an IC prototype design using the TSMC 65-nm CMOS technology. It will be shown that the IC achieves 12 bits of resolution from 1020 memory elements, whereas an unsegmented $\Sigma \Delta $ -DAC uses 4095 elements to obtain the same resolution. This is about a 75% savings in memory elements. The segmented prototype occupies 0.5 mm 2 of silicon area, whereas the unsegmented design occupies 0.77 mm 2 for the same resolution. A 35% silicon area savings compared with its unsegmented counterpart. A second prototype implements the segmented $\Sigma \Delta $ -DAC architecture using discrete components. The discrete prototype achieves 16 bits of resolution from 1020 memory elements, whereas the unsegmented counterpart uses 65 535 bits for the same resolution. This is a 98% saving in memory elements.
14 February 2020 in IEEE Open Journal of Circuits and Systems
Settling time is an important performance metric in digital-to-analog converters (DACs) that are used for dynamic calibration applications. To obtain an area efficient DAC design, periodic sequences are generated from sigma-delta modulators (ΣΔ Ms) using software, stores the sequence in memory and then passes it to a low-pass filter (LPF). In this brief, the sigma-delta (ΣΔ) bitstream generated in software will be optimized such that it yields a system that settles faster and is more area efficient. Two optimization routines are used, namely, serial method and random method algorithms. The random method is chosen to optimize the ΣΔ bitstreams for its computational simplicity. It will be shown, that using the random method routine provides at least 46 improvement in settling time performance of a 12-bit DAC, used in the paper as a design example. Moreover, it offers silicon area savings by at least 10% for resistor components and 35% for capacitor components. Similar results were obtained for 8 to 11 bits of resolution.
14 August 2025 in IEEE Transactions on Circuits and Systems I: Regular Papers
Cascading gain stages in CMOS Operational Transconductance Amplifiers (OTAs) has become a necessity in applications with high gain requirements, where the contribution of each stage to the overall gain is well-known and carefully designed. Many of these applications also impose requirements on speed, including a minimum Slew-Rate (SR) to ensure signal fidelity, however the impact of individual gain stages on the overall SR in multi-stage OTAs has been difficult to characterize–let alone carefully design. The difficulty arises due to the complexity of the compensation networks involved in these OTAs. This paper presents a systematic design approach for achieving a target SR in multi-stage CMOS OTAs, enabled through the utility of a novel analytical model for estimating the lower-bound Slew-Rate in multi-stage OTAs. The model evaluates individual currents and equivalent capacitances at the output node of each stage, providing insights on the dominant node slowing down the overall SR. For generality, the model establishes the SR analysis based on N-stage designs, and considers widely employed compensation networks. Example designs, with post-layout simulations and measurements of a 3- and a 4-stage CMOS OTA, and with post-layout simulations of a 5-stage CMOS OTA, are presented for validating the model’s utility. The results show strong agreement between theoretical, simulated, and measured SR values, confirming the model’s reliability in estimating the lower-bound SR, and its utility in a systematic design-for-SR approach in multi-stage CMOS OTAs.