In this Letter, we report an inkjet-printed resistive switching device based on an Ag/ZnO/Au structure. The device exhibits bipolar resistive switching behavior, a low operation voltage of about 0.7 V, a high on/off ratio of 107, a long retention time exceeding 104 s, and good endurance. The conduction mechanism of the device in low and high resistive states was studied and showed good consistency with the theory of Ohmic and space charge limited conduction mechanisms, respectively.
Electrolyte‐gated transistors (EGTs) represent an interesting alternative to conventional dielectric‐gating to reduce the required high supply voltage for printed electronic applications. Here, a type of ink‐jet printable ion‐gel is introduced and optimized to fabricate a chemically crosslinked ion‐gel by self‐assembled gelation, without additional crosslinking processes, e.g., UV‐curing. For the self‐assembled gelation, poly(vinyl alcohol) and poly(ethylene‐alt‐maleic anhydride) are used as the polymer backbone and chemical crosslinker, respectively, and 1‐ethyl‐3‐methylimidazolium trifluoromethanesulfonate ([EMIM][OTf]) is utilized as an ionic species to ensure ionic conductivity. The as‐synthesized ion‐gel exhibits an ionic conductivity of ≈5 mS cm−1 and an effective capacitance of 5.4 µF cm−2 at 1 Hz. The ion‐gel is successfully employed in EGTs with an indium oxide (In2O3) channel, which shows on/off‐ratios of up to 1.3 × 106 and a subthreshold swing of 80.62 mV dec−1.
22 June 2020 in Physica Status Solidi (RRL) – Rapid Research Letters
Printed and flexible metal‐oxide transistor technology has recently demonstrated great promise due to its high performance and robust mechanical stability. Herein, fully printed inverter structures using electrolyte‐gated oxide transistors on a flexible polyimide (PI) substrate are discussed in detail. Conductive graphene ink is printed as the passive structures and interconnects. The additive printed transistors on PI substrates show an ratio of and show mobilities similar to the state‐of‐the‐art printed transistors on rigid substrates. Printed meander structures of graphene are used as pull‐up resistances in a transistor–resistor logic to create fully printed inverters. The printed and flexible inverters show a signal gain of 3.5 and a propagation delay of 30 ms. These printed inverters are able to withstand a tensile strain of 1.5% following more than 200 cycles of mechanical bending. The stability of the electrical direct current (DC) properties has been observed over a period of 5 weeks. These oxide transistor‐based fully printed inverters are relevant for digital printing methods which could be implemented into roll‐to‐roll processes.
15 September 2022 in Advanced Engineering Materials
High‐entropy alloys (HEAs) or complex concentrated alloys (CCAs) offer a huge research area for new material compositions and potential applications. Since the combination of several elements sometimes leads to unexpected and unpredictable material properties. In addition to the element combinations, the optimization of the element proportions in CCAs and HEAs is also a decisive factor in tailoring desired material properties. However, it is almost impossible to achieve the composition and characterization of CCAs and HEAs with a sufficient number of compositions by conventional experiments. Therefore, an optimized high‐throughput magnetron sputtering synthesis to fabricate a new HEA gradient layer of six elements is presented. With this approach, the compositional space of the HEA system CrMoNbTaVW can be studied in different subsections to determine the influence of the individual elements and their combinations on the structure, morphology, and physical properties (hardness and resistivity). It is found that the Cr‐, Ta‐, and W‐rich phases, which have a grain size of 10–11 nm, exhibit the hardest mechanical properties, whereas V‐, Ta‐, and Cr‐rich compounds exhibit the highest electrical resistivity. The combination of high‐throughput synthesis, automated analysis tools, and automated data interpretation enables rapid and time‐efficient characterization of the novel CrMoNbTaVW gradient film.