zhou zhikai

Dr. zhou zhikai


Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
14 September 2019 in Metals
Verified
Journal Article
Open access
PDF file
EKEdwin Eyram Klu
Edwin Eyram Klu
DSDan SONG
Dan SONG
CLChen Li
Chen Li
GWGuowei Wang
Guowei Wang
ZZzhou zhikai
zhou zhikai
JJJinghua Jiang
Jinghua Jiang
In this study, a high-strength Mg-9Li alloy was developed via multi-pass equal-channel-angular-pressing (ECAP) and post rolling, of which the yield tensile stress (YTS) and ultimate tensile stress (UTS) were 166 MPa and 174 MPa representing about 219% and 70% increase in YTS and UTS respectively, compared to the cast alloy. The cast alloy was ECAP processed at 200 °C for 4, 8, and 16 passes, followed by room-temperature rolling to a total thickness reduction of 50%. The 8-passes ECAPed (E8) alloy presented the best strength of all the ECAPed alloys, and the post rolling endowed the alloy (E8R) further strengthening and the best strength of all the alloys. Grain-boundary strengthening and dislocation strengthening were the two major factors for the high strength of the processed alloys. The α-Mg phase grains were greatly refined to about 2 μm after 8-passes ECAP, and was further refined to about 800 nm ~1.5 μm after rolling. Significant grain refinement endowed the alloy with sufficient grain-boundary strengthening. Profuse intragranular dislocation accumulated in the deformed matrix, leading to the significant dislocation hardening of the alloy. Rolling-induced strong basal texture of the α-Mg phase also enhanced the further strengthening of the E8R alloy.

5 October 2019 in Materials
Verified
Journal Article
Open access
PDF file
ZZzhou zhikai
zhou zhikai
DSDan SONG
Dan SONG
Ningning LiangNingning Liang
Ningning Liang
HJHaiyang Jiang
Haiyang Jiang
BGBo Gao
Bo Gao
XMXiaolong Ma
Xiaolong Ma
In this paper, the effect of the equal-channel-angular-pressed (ECAPed) substrate on the coating formation and anticorrosion performance of the anodized Al–11Si alloy was systematically investigated. The ECAP process dramatically refines both Al and Si phases of the alloy. The parallel anodizing circuit is designed to enable a comparative study of anodizing process between the cast and the ECAPed alloys by tracking their respective anodizing current quota. The optimum coatings of both alloys were obtained after anodization for 30 min. The ECAPed alloy attained a thicker, more compact, and more uniform coating. Energetic crystal defects in the fine Al grains of the ECAPed substrate promote the anodizing reaction and lead to the thicker coating. Fragmented and uniformly distributed fine Si particles in the ECAPed alloy effectively suppress the coating cracks, enhancing the compactness of the coating. Overall, the ECAP-coated sample exhibits the best anticorrosion performance, which is evidenced by the concurrently enhanced prevention of coating and improved corrosion resistance of the substrate.

28 February 2020 in Coatings
Verified
Journal Article
Open access
PDF file
GWGuowei Wang
Guowei Wang
DSDan SONG
Dan SONG
ZZzhou zhikai
zhou zhikai
EKEdwin Eyram Klu
Edwin Eyram Klu
YLYi Liu
Yi Liu
AMAibin Ma
Aibin Ma
This work analyzes the effects of ultrafine aluminum (Al) grains on the anodizing coating reaction and anticorrosion performance of anodized industrial pure Al. Equal-channel angular pressing (ECAP) was applied to cast pure Al continuously for 16 passes at room temperature, and its average grain size was dramatically refined to about 1.5 μm. The ultrafine-grain (UFG) pure Al was further anodized with a cast sample via a parallel anodizing circuit at a constant total input current. Benefited by the higher volume fraction of grain boundaries and higher internal energy of the UFG substrate, the anodizing process of the ECAP-processed pure Al was significantly accelerated, showing a more intense initial anodizing reaction, a faster initial coating thickening, and much earlier porous-layer formation compared to the cast sample. As the anodizing reaction continued, the newly formed thicker coating of the ECAP-coated sample significantly hindered the diffusion process, weakening the thermodynamic advantage and decreasing the anodizing current of the ECAP-processed sample. During the entire anodizing duration, the ECAP-processed pure Al experienced gradually decreased anodizing current, while the cast sample experienced increased anodizing current. Because of the more total reaction, the ECAP-coated sample always maintained a relatively thicker coating and better anticorrosion performance during the entire anodizing duration.