A phased-array test platform for studying the self-adapting capabilities of conformal antennas is developed and presented. Specifically, a four-port 2.45-GHz receiver with voltage controlled phase shifters and attenuators is designed along with four individual printed microstrip patch antennas attached to a conformal surface. Each antenna is connected to the corresponding receiver port with a flexible SMA cable. It is shown that with appropriate phase compensation, the distorted radiation pattern of the array can be recovered as the surface of the conformal array changes shape. This pattern recovery information is then used to develop a new self-adapting flexible 1 × 4 microstrip antenna array with an embedded flexible sensor system. In particular, a flexible resistive sensor is used to measure the deformation of the substrate of a conformal antenna array, while a sensor circuit is used to measure the changing resistance. The circuit then uses this information to control the individual voltage of the phase shifters of each radiating element in the array. It is shown that with appropriate phase compensation, the radiation properties of the array can be autonomously recovered as the surface of the flexible array changes shape during normal operation. Throughout this work, measurements are shown to agree with analytical solutions and simulations.

Self-adapting conformal antennas for changing spherical surfaces are investigated in this work. More specifically, the theory on the relationship between the radius of the spherical surface, element spacing of the conformal array and required phase compensation is developed. Initially, for theoretical validation, a 4 × 4 phased array antenna is assembled with individual microstrip antennas used as the radiators at 2.47 GHz. Each antenna is connected to a commercially available voltage controlled phase shifter with identical SMA cables and then each phase shifter is connected to a port on a sixteen-way power divider. This phased-array antenna allows for convenient placement of individual patches on the spherical surface and precise phase control. For further validation, a second 4 × 4 phased-array antenna with embedded phase shifters and a sensing circuit is manufactured. The sensing circuit is used to measure the radius of curvature of the spherical surface and use this information to autonomously apply the appropriate phase compensation, based on the previous theoretical developments, to recover the radiation pattern of the array for different spherical surfaces at 2.47 GHz. Overall, good agreement between theory, simulation and experimental data is shown and that it is possible to recover the radiation pattern autonomously.

Microwaves are non-ionizing electromagnetic radiation with waves of electrical and magnetic energy transmitted at different frequencies. They are widely used in various industries, including the food industry, telecommunications, weather forecasting, and in the field of medicine. Microwave applications in medicine are relatively a new field of growing interest, with a significant trend in healthcare research and development. The first application of microwaves in medicine dates to the 1980s in the treatment of cancer via ablation therapy; since then, their applications have been expanded. Significant advances have been made in reconstructing microwave data for imaging and sensing applications in the field of healthcare. Artificial intelligence (AI)-enabled microwave systems can be developed to augment healthcare, including clinical decision making, guiding treatment, and increasing resource-efficient facilities. An overview of recent developments in several areas of microwave applications in medicine, namely microwave imaging, dielectric spectroscopy for tissue classification, molecular diagnostics, telemetry, biohazard waste management, diagnostic pathology, biomedical sensor design, drug delivery, ablation treatment, and radiometry, are summarized. In this contribution, we outline the current literature regarding microwave applications and trends across the medical industry and how it sets a platform for creating AI-based microwave solutions for future advancements from both clinical and technical aspects to enhance patient care.

As the usage of wireless technology grows, it demands more complex architectures and conformal geometries, making the manufacturing of radio frequency (RF) systems challenging and expensive. The incorporation of emerging alternative manufacturing technologies, like additive manufacturing (AM), could consequently be a unique and cost-effective solution for flexible RF and microwave circuits and devices. This work presents manufacturing methodologies of 3D-printed conformal microstrip antennas made of a commercially available conductive filament, Electrifi, as the conductive trace on a commercially available nonconductive filament, NinjaFlex, as the substrate using the fused filament fabrication (FFF) method of AM technology. Additionally, a complete high frequency characterization of the prototyped antenna was studied and presented here through a comparative analysis between full-wave simulation and measurements in a fully calibrated anechoic chamber. The prototyped antenna measures 65.55 × 55.55 × 1.2 mm³ in size and the measured results show that the 3D-printed Electrifi based patch antenna achieved very good impedance matching at a resonant frequency of 2.4 GHz and a maximum antenna gain of −2.78 dBi. Finally, conformality performances of the developed antenna were demonstrated by placing the antenna prototype on five different cylindrical curved surfaces for possible implementation in flexible electronics, smart communications, and radar applications.

New research on wearable electronics, domotics, flexible circuits, and RF applications on conformal surfaces have used the advancements of material science and additive manufacturing technology. Parallelly, the limited design specifications of industrially available PCB substrates (i.e., flat substrates) has stimulated a de novo exploration for more complex electronic circuits with versatile geometries. In this paper, the development of a microstrip transmission line using additive manufacturing technology and Electrifi conductive filament is reported for the first time. The simulated and measured transmission properties of the design are also compared and presented.

Evolution of mobile broadband is ensured by adopting a unified and more capable radio interface (RI). For ubiquitous connectivity among a wide variety of wireless applications, the RI enables the adoption of an adaptive bandwidth with high spectrum flexibility. To this end, the modern-day communication system needs to cater to extremely high bandwidth, starting from below 1 GHz to 100 GHz, based on different deployments. This instigates the creation of a platform called the Internet of Everything (IoE), which is based on the concept of all-round connectivity involving humans to different objects or things via sensors. In simple words, IoE is the intelligent connection of people, processes, data, and things. To enable seamless connectivity, IoE resorts to low-cost, compact, and flexible broadband antennas, RFID-based sensors, wearable electromagnetic (EM) structures, circuits, wireless body area networks (WBAN), and the integration of these complex elements and systems. IoE needs to ensure broader information dissemination via simultaneous transmission of data to multiple users through separate beams and to that end, it takes advantage of metamaterials. The precise geometry and arrangement of metamaterials enable smart properties capable of manipulating EM waves and essentially enable the metamaterial devices to be controlled independently to achieve desirable EM characteristics, such as the direction of propagation and reflection. This review paper presents a comprehensive study on next-generation EM devices and techniques, such as antennas and circuits for wearable and sub 6 GHz 5G applications, WBAN, wireless power transfer (WPT), the direction of arrival (DoA) of propagating waves, RFID based sensors for biomedical and healthcare applications, new techniques of metamaterials as well as transformation optics (TO) and its applications in designing complex media and arbitrary geometry conformal antennas and optical devices that will enable future IoE applications.