As the usage of wireless technology grows, it demands more complex architectures and conformal geometries, making the manufacturing of radio frequency (RF) systems challenging and expensive. The incorporation of emerging alternative manufacturing technologies, like additive manufacturing (AM), could consequently be a unique and cost-effective solution for flexible RF and microwave circuits and devices. This work presents manufacturing methodologies of 3D-printed conformal microstrip antennas made of a commercially available conductive filament, Electrifi, as the conductive trace on a commercially available nonconductive filament, NinjaFlex, as the substrate using the fused filament fabrication (FFF) method of AM technology. Additionally, a complete high frequency characterization of the prototyped antenna was studied and presented here through a comparative analysis between full-wave simulation and measurements in a fully calibrated anechoic chamber. The prototyped antenna measures 65.55 × 55.55 × 1.2 mm³ in size and the measured results show that the 3D-printed Electrifi based patch antenna achieved very good impedance matching at a resonant frequency of 2.4 GHz and a maximum antenna gain of −2.78 dBi. Finally, conformality performances of the developed antenna were demonstrated by placing the antenna prototype on five different cylindrical curved surfaces for possible implementation in flexible electronics, smart communications, and radar applications.

A compact reconfigurable UWB MIMO antenna with four radiators that accomplish on-demand band rejection from 4.9 to 6.3 GHz is presented. An LC stub is connected to the ground plane by activating the PIN diode for each radiator. Two radiators are placed perpendicular to each other to exploit the polarization diversity on a compact 25 × 50 mm ${}^2$ FR4 laminate. Two additional radiators are then fixed obliquely on the same laminate (without increasing size) in angular configuration at ±45 ${}^{\circ }$ perpendicular to the first two planar radiators still exploiting polarization diversity. The design is validated by prototyping and comparing the results with the simulated ones. On demand band rejection through the use of PIN diodes, wide impedance matching (2–12 GHz), high isolation amongst the radiators, compactness achieved by angular placement of the radiators, low gain variation over the entire bandwidth, band rejection control achieved by adjusting the gap between stub and ground plane, and low TARC values makes the proposed design very suitable for commercial handheld devices (i.e., Huawei E5785 and Netgear 815S housings). The proposed configuration of the UWB MIMO radiators has been investigated first time as per authors’ knowledge.

New research on wearable electronics, domotics, flexible circuits, and RF applications on conformal surfaces have used the advancements of material science and additive manufacturing technology. Parallelly, the limited design specifications of industrially available PCB substrates (i.e., flat substrates) has stimulated a de novo exploration for more complex electronic circuits with versatile geometries. In this paper, the development of a microstrip transmission line using additive manufacturing technology and Electrifi conductive filament is reported for the first time. The simulated and measured transmission properties of the design are also compared and presented.

Evolution of mobile broadband is ensured by adopting a unified and more capable radio interface (RI). For ubiquitous connectivity among a wide variety of wireless applications, the RI enables the adoption of an adaptive bandwidth with high spectrum flexibility. To this end, the modern-day communication system needs to cater to extremely high bandwidth, starting from below 1 GHz to 100 GHz, based on different deployments. This instigates the creation of a platform called the Internet of Everything (IoE), which is based on the concept of all-round connectivity involving humans to different objects or things via sensors. In simple words, IoE is the intelligent connection of people, processes, data, and things. To enable seamless connectivity, IoE resorts to low-cost, compact, and flexible broadband antennas, RFID-based sensors, wearable electromagnetic (EM) structures, circuits, wireless body area networks (WBAN), and the integration of these complex elements and systems. IoE needs to ensure broader information dissemination via simultaneous transmission of data to multiple users through separate beams and to that end, it takes advantage of metamaterials. The precise geometry and arrangement of metamaterials enable smart properties capable of manipulating EM waves and essentially enable the metamaterial devices to be controlled independently to achieve desirable EM characteristics, such as the direction of propagation and reflection. This review paper presents a comprehensive study on next-generation EM devices and techniques, such as antennas and circuits for wearable and sub 6 GHz 5G applications, WBAN, wireless power transfer (WPT), the direction of arrival (DoA) of propagating waves, RFID based sensors for biomedical and healthcare applications, new techniques of metamaterials as well as transformation optics (TO) and its applications in designing complex media and arbitrary geometry conformal antennas and optical devices that will enable future IoE applications.

The interests in the effects of radio frequency (RF) on biological systems has increased. This interest has increased partially due to the advancements and increase implementations of RF into technology. As research in the area has progressed, the reliability and reproducibility of those experiments has not crossed multidisciplinary boundaries. Therefore, as researchers, it is imperative to understand the various exposure systems available as well as the aspects, both electromagnetic and biological, needed to produce a sound exposure experiment. This systematic review examines common radio frequency exposure methods for both in vitro and in vivo studies. For in vitro studies, discussion of possible biological limitations to consider were also emphasized. The validity of the examined methods, for both in vitro and in vivo, were analyzed by discussing the advantages and disadvantages of each. This review offers guidance for researchers to assist in the development of an RF exposure experiment that crosses current multidisciplinary boundaries.