One way to reduce CO₂ emissions is to replace conventional energy sources with renewable ones. In order to encourage prosumers to invest in renewable energy, EU Member States are developing renewable energy subsidy programs. In Poland, in the years 2019–2020, the “My Electricity” program was implemented, co-financing was up to 50% of eligible costs (max PLN 5000, i.e., EUR 1111), and the total cost of the program was 251 million euro. During this period, around 400,000 prosumer installations were created in Poland, including over 220,000 prosumer PV Installations under the My Electricity program. The total power of the installation under the “My Electricity” program was 1.295 GWp with an average installation power of 5.72 kWp. It is estimated that the micro-installations will produce approx. 1.4 TWh of electricity annually. Depending on the replaced source of electricity (coal, gas, mix), in the next 30 years, it will help to avoid 26.2–42.7 million Mg of greenhouse gases calculated as carbon dioxide equivalents (CO_2eq). The coefficient of subsidy expenditure from the “My Electricity” program was 194 EUR/kWp, and in the next 30 years, it will be 6.52 EUR/MWh. The investment in PV will save EUR 1550 million, which would have to be incurred for the purchase of CO₂ emission permits.

The transition to low-carbon heating systems is fundamental to achieving climate neutrality, particularly within the building sector, which accounts for a significant share of global greenhouse gas emissions. Among various technologies, heat pumps have emerged as a leading solution due to their high energy efficiency and potential to significantly reduce CO₂ emissions, especially when powered by renewable electricity. This systematic review synthesizes findings from the recent literature, including peer-reviewed studies and industry reports, to evaluate the technical performance, environmental impact, and deployment potential of air source, ground source, and water source heat pumps. This review also investigates life cycle greenhouse gas emissions, the influence of geographical energy mix diversity, and the integration of heat pumps within hybrid and district heating systems. Results indicate that hybrid HP systems achieve the lowest specific GHG emissions (0.108 kgCO₂eq/kWh of heat delivered on average), followed by WSHPs (0.018 to 0.216 kgCO₂eq/kWh), GSHPs (0.050–0.211 kgCO₂eq/kWh), and ASHPs (0.083–0.216 kgCO₂eq/kWh). HP systems show a potential GHG emission reduction of up to 90%, depending on the kind of technology and energy mix. Despite higher investment costs, the lower environmental footprint of GSHPs and WSHPs makes them attractive options for decarbonizing the building sector due to better performance resulting from more stable thermal input and higher SCOP. The integration of heat pumps with thermal storage, renewable energy, and smart control technologies further enhances their efficiency and climate benefits, regardless of the challenges facing their market potential. This review concludes that heat pumps, particularly in hybrid configurations, are a cornerstone technology for sustainable building heat supply and energy transition.

Hybrid photovoltaic installations, defined as on-grid PV system in cooperation with battery energy storage system (BESS), are still rare among the typical investors because the investment cost of the hybrid installation is significantly higher than the one of the on-grid system. However, while considering the broader perspective, such as environmental or technological aspects, the mentioned solution can be competitive with photovoltaic on-grid systems and therefore should be carefully tested in the widest possible context. In this study, the authors compared 3.05 kW of peak power hybrid and on-grid installations operating in temperate climate conditions (Eastern Poland) using economic indicators, such as dynamic generation cost (DGC) and benefit–cost rate (BCR); environmental impact indicators (IMPACT 2002+ and GWP 100a) determined using Life Cycle Assessment (LCA); and technological aspects consideration, including the reliability of examined systems. Creating a ranking of the considered solutions based on the equal weighting factors assigned to the appropriate features allows indicating the technological areas where the competitiveness of hybrid systems justifies the increased investment costs. One such area is business, where the economic criterion, the only negatively assessed one in the standard operation, can be radically changed by the possible financial losses due to interruption of energy supply.

Efforts to direct the economies of many countries towards low-carbon economies are being made in order to reduce their impact on global climate change. Within this process, replacing fossil fuels with hydrogen will play an important role in the sectors where electrification is difficult or technically and economically ineffective. Hydrogen may also play a critical role in renewable energy storage processes. Thus, the global hydrogen demand is expected to rise more than five times by 2050, while in the European Union, a seven-fold rise in this field is expected. Apart from many technical and legislative barriers, the environmental impact of hydrogen production is a key issue, especially in the case of new and developing technologies. Focusing on the various pathways of hydrogen production, the essential problem is to evaluate the related emissions through GHG accounting, considering the life cycle of a plant in order to compare the technologies effectively. Anion exchange membrane (AEM) electrolysis is one of the newest technologies in this field, with no LCA studies covering its full operation. Thus, this study is focused on a calculation of the carbon footprint and economic indicators of a green hydrogen plant on the basis of a life cycle assessment, including the concept of a solar-to-hydrogen plant with AEM electrolyzers operating under Polish climate conditions. The authors set the range of the GWP indicators as 2.73–4.34 kgCO_2eq for a plant using AEM electrolysis, which confirmed the relatively low emissivity of hydrogen from solar energy, also in relation to this innovative technology. The economic profitability of the investment depends on external subsidies, because, as developing technology, the AEM electrolysis of green hydrogen from photovoltaics is still uncompetitive in terms of its cost without this type of support.

Global energy consumption is increasing every year, and, despite their many negative impacts, fossil fuels are a major source of energy, but their reserves are gradually depleting. One of the promising but underutilized resources is plant biomass (phytomass). The main problem of plant biomass combustion is the low melting temperature of ash, but there are also problems with corrosion of heat exchangers and clogging of heat-exchanging surfaces. This work is concerned with the production of straw pellets in order to increase the melting temperature of ash by adding an additive. The paper sludge contains substances that can increase the melting point of ash and was therefore added to the pellet samples. This additive was mixed with straw in ratios from 90:10, 80:20 and 70:30 (straw/paper sludge). The use of paper sludge showed positive effects on increasing the melting temperature of the ash samples. The deformation temperature of the ash has already risen from 1020 to 1260 °C after the addition of 10% sludge, which is comparable to wood pellets.

The increasing costs related to the use of primary energy carriers, and greater social awareness related to the need for energy saving, necessitate the use of renewable energy sources, including solar radiation. The Trombe wall (thermal storage wall—TSW) is an indirect passive solar energy system solution, aimed at obtaining, storing, and transferring thermal energy into buildings. However, there is no comprehensive information on the impact of the use of such solutions on environmental performance in the life cycle of buildings, especially those located in temperate climates. The aim of this paper is therefore to determine the environmental impact of the construction of barriers using phase change materials (PCM) from the perspective of the life cycle of a model building conforming to the current Polish energy standard (EP < 70 kWh/(m²∙yr)). The subject of the research is the structure of a TSW using phase change materials and a reference wall with a maximum overall heat transfer coefficient of 0.2 W/m²K. A comprehensive computational model of a residential building located in Rzeszów, Poland, was created, taking into account the thermal parameters of the analyzed structure of the wall and its operation under real, specific climatic conditions, as well as the environmental characteristics. High-quality input data (based on real, long-term measurements) were used to conduct a Life Cycle Assessment of the analyzed variants. As a result, the energetic and environmental efficiency of the analyzed thermal storage wall, from the perspective of the whole building’s life cycle, were assessed. According to the analyzed data, a TSW modified with paraffin enables the reduction of the energy requirements for heating by 11.3%, and the payback period of the environmental load does not exceed 1 (GWP) and 5 (IMPACT2002+) years, which were lower than the monitored period of operation.