Maosheng Zhang

Dr. Maosheng Zhang

zhejiang university
orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
18 December 2019 in Micromachines
Verified
Journal Article
Open access
PDF file
MZMaosheng Zhang
Maosheng Zhang
NRNa Ren
Na Ren
QGQing Guo
Qing Guo
XZXiangwen Zhu
Xiangwen Zhu
JZJunming Zhang
Junming Zhang
KSKuang Sheng
Kuang Sheng
In this work, a 1200V/200A full-SiC half-bridge power module was fabricated for high-power high-frequency application, and the characteristics of gate-source voltage ( v g s ) at turn-on transient under different output power was investigated via experiments, modeling, and simulation. Also, the comparison of the v g s characteristics between the upper-side and lower-side was conducted. From experiments, the v g s characteristics show negative spike issue and it becomes severe under higher output power conditions. On the other hand, the upper-side and lower-side show different characteristics, namely, the v g s spike of upper-side is superimposed by a 83.3 MHz high frequency oscillation during the process of v g s being pulled down, while the v g s spike of lower-side contains no oscillation. The mechanisms behind the influence of output power on the v g s spike characteristics and their difference between the upper-side and lower-side were studied via modeling and simulation. Equivalent RLC (resistance-inductance-capacitance) circuit models were proposed and established for the gate driver loops of the upper-side and lower-side based on the internal structure of the power module. With the help of the proposed models, v g s characteristics of the upper-side and lower-side were simulated and compared with the experimental results. The trend of changes in the v g s pulling-down and oscillation amplitude along with the increasing output power from simulation are consistent with that of the experimental results. In addition, different conditions of gate resistance for the SiC power module are compared. Through the comparison between the experiments and simulations, the validity of the proposed equivalent RLC circuit model and the rationality of the analysis about the mechanisms behind the v g s characteristics at turn-on transient for SiC half-bridge power module are confirmed.

23 November 2020
Verified
Conference Paper
Closed access
MZMaosheng Zhang
Maosheng Zhang
NRNa Ren
Na Ren
QGQing Guo
Qing Guo
WYWenxi Yao
Wenxi Yao
KSKuang Sheng
Kuang Sheng
Silicon carbide metal oxide semiconductor field effect transistor (SiC-MOSFET) power devices have the advantage in high-power and high-frequency applications over silicon insulated gate bipolar transistor (Si-IGBT), due to the superior properties of fast switching speed and low switching loss. In order to meet the requirements of the applications of higher power and higher switching frequency for power devices, the power module based high power density integration becomes the mainstream trend of the development of SiC devices, but the highly integration also increase the concern about the coupling failure by near-filed radiated emission due to fast switching performance of SiC power module. For this problem, in this paper a buck converter based on SiC power module with 62mm standard outline has been built, the near-filed radiated emission of the module has been investigated, and finally, the spectrum and spatial distribution of near-field radiated emission electromagnetic interference (EMI) of the module have been disclosed.

24 July 2020 in Energies
Verified
Journal Article
Open access
PDF file
MZMaosheng Zhang
Maosheng Zhang
NRNa Ren
Na Ren
QGQing Guo
Qing Guo
KSKuang Sheng
Kuang Sheng
The SiC (silicon carbide) high-power module has great potential to replace the IGBT (insulated gate bipolar transistor) power module in high-frequency and high-power applications, due to the superior properties of fast switching and low power loss, however, when the SiC high-power module operates under inappropriate conditions, the advantages of the SiC high-power module will be probably eliminated. In this paper, four kinds of SiC high-power modules are fabricated to investigate fast switching performance. The variations in characteristics of drain-source voltage at turn-on transient under the combined conditions of multiple factors are studied. A characteristic of voltage plateau is observed from the drain-source voltage waveform at turn-on transient in the experiments, and the characteristic is reproduced by simulation. The mechanism behind the voltage plateau is studied, and it is revealed that the characteristic of drain-source voltage plateau is a reflection of the miller plateau effect of gate-source voltage on drain-source voltage under the combined conditions of fast turn-on speed and low DC bus voltage, while the different values of drain-source voltage plateau are attributed to the discrepancy of structure between upper-side and lower-side in the corresponding partial path of the drain circuit loop inside the module, with the standard 62 mm package outline.

29 November 2020
Verified
Conference Paper
Closed access
MZMaosheng Zhang
Maosheng Zhang
SYShu Yang
Shu Yang
KSKuang Sheng
Kuang Sheng
In this work, a 4-in-1 integrated PCU module was developed for the application of hybrid electrical vehicles. It realized the integration of power dies, direct current bus capacitors, current flow sensors and liquid-cooler in physical structure, and the integration of the boost circuit, power generator, motor drives and a multiplexing charger in functional units of power converter. The thermal resistance and capacitance (RC) characteristics for the power switch dies were studied and compared by experiments. It has been revealed that the difference of the RC characteristics among different power converter units depends on the types and the parallel number of power switch dies, while the difference of the RC characteristics between the upper-side and lower-side within a single power converter unit is attributed to the distinct spacing between the paralleled power switch dies and layout design of the upper-copper-layer of the direct bonding copper (DBC). Based on this unique RC characteristics of the developed 4-in-1 integrated PCU module and the power loss for the current operating conditions, the volume flow rate of the coolant for the PCU module has been optimized by simulations. This approach could minimize the risk of local overheating of the power dies in the module which is particularly important for the high-integration design of the developed PCU module.

16 April 2021 in Electronics
Verified
Journal Article
Open access
PDF file
MZMaosheng Zhang
Maosheng Zhang
YBYu Bai
Yu Bai
SYShu Yang
Shu Yang
KSKuang Sheng
Kuang Sheng
With the increasing integration density of power control unit (PCU) modules, more functional power converter units are integrated into a single module for applications in electric vehicles or hybrid electric vehicles (EVs/HEVs). Different types of power dies with different footprints are usually placed closely together. Due to the constraints from the placement of power dies and liquid cooling schemes, heat-flow paths from the junction to coolant are possibly inconsistent for power dies, resulting in different thermal resistance and capacitance (RC) characteristics of power dies. This presents a critical challenge for optimal liquid cooling at a low cost. In this paper, a highly integrated PCU module is developed for application in EVs/HEVs. The underlying mechanism of the inconsistent RC characteristics of power dies for the developed PCU module is revealed by experiments and simulations. It is found that the matching placement design of power dies with a heat sink structure and liquid cooler, as well as a liquid cooling scheme, can alleviate the inconsistent RC characteristics of power dies in highly integrated PCU modules. The findings in this paper provide valuable guidance for the design of highly integrated PCU modules.