Luis Bejar

Luis Bejar


Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
19 July 2018 in Matéria (Rio de Janeiro)
Verified
Journal Article
Open access
PDF file
Engelbert Huape PadillaEngelbert Huape Padilla
Engelbert Huape Padilla
Ariosto MedinaAriosto Medina
Ariosto Medina
Claudio AguilarClaudio Aguilar
Claudio Aguilar
Ismeli AlfonsoIsmeli Alfonso
Ismeli Alfonso
LBLuis Bejar
Luis Bejar
Nickel aluminides have been extensively studied in recent decades to replace superalloys, in some components of aircraft turbines, because they have excellent corrosion resistance. Many industrial cities have the problem of air pollution, which has forced the study of the degradation of these alloys in the presence of acid rain. The aim of this work is to study the electrochemical corrosion behavior of nickel aluminides in a medium of simulated acid rain. Potentiodynamic Polarization, Linear polarization resistance curves, Rp, Nyquist data and Bode curves obtained by electrochemical impedance spectroscopy were used to study the corrosion behavior of two intermetallic compounds. The polarization curves show that both intermetallic Ni3Al and NiAl have very similar corrosion potential, showing a slightly nobler behavior the NiAl intermetallic. The intermetallic Ni3Al has an active-passive behavior where the anode branch presents a general dissolution of the alloy, indicating that it is under cathodic control. NiAl intermetallic shows an active dissolution region, followed by a passive behavior. At longer immersion times, Ni3Al intermetallic has a higher polarization resistance, which means a lower corrosion rate.

5 December 2019 in International Journal of Chemical Reactor Engineering
Verified
Journal Article
Closed access
PDF file
SDS. Domínguez-García
S. Domínguez-García
LBLuis Bejar
Luis Bejar
Rafael Huirache-AcuñaRafael Huirache-Acuña
Rafael Huirache-Acuña
JLJavier Lara-Romero
Javier Lara-Romero
Rafael Maya-YescasRafael Maya-Yescas
Rafael Maya-Yescas
Lubricant reactions in internal combustion engines follow complex reaction pathways, in which oil (hydrocarbons) and additives form protecting films (known as tribofilms) on the surfaces of the cylinder-piston couple. Up-to-date there is not a fundamental model useful to describe the chemistry involved in formation of these tribofilms, and degradation of oils and additives as result of working time of the engine. One of the main problems associated is the impossible measuring of the actual phenomena inside the engine, at working conditions. In order to model formation of tribofilms, starting by lumping two main groups of lubricating molecules, anti-shear and anti-wear, the lumped kinetics model for degradation products was solved, based on actual data collected in commercial engine workshops. Later these two-lump reaction schemes were delumped into two new systems, each one consisting of three lumps, in order to infer lubricant reaction pathways that form tribofilms and degrade lubricants. Distribution of anti-shear and anti-wear lubricants in tribofilms was predicted by simulation of these two delumped schemes.

1 September 2017 in Soldagem & Inspeção
Verified
Journal Article
Open access
PDF file
MRManuel Rodríguez
Manuel Rodríguez
LPLorenzo Perdomo
Lorenzo Perdomo
LBLuis Bejar
Luis Bejar
JMJosé A. Moreno
José A. Moreno
Ariosto MedinaAriosto Medina
Ariosto Medina
Ismeli AlfonsoIsmeli Alfonso
Ismeli Alfonso
Las aleaciones para el relleno superficial Fe-Mn-C (Hadfield) han demostrado una excelente resistencia al desgaste bajo altas cargas dinámicas. En los últimos años se han realizado numerosos estudios para aumentar la resistencia al desgaste y mejorar su desempeño, a través de la introducción de otros elementos de aleación. En el presente trabajo se investiga la microestructura y dureza de los depósitos de relleno con alto contenido de Mn y adiciones de 1.2% de V y 2.4% de Si. Los depósitos estudiados se realizaron utilizando electrodos tubulares revestidos fabricados a escala de laboratorio. Las fases y microconstituyentes en el metal depositado se identificaron mediante microscopía óptica (MO), electrónica de barrido (MEB), difracción de rayos X (DRX), dureza y microdureza. De acuerdo a los resultados obtenidos, la adición de V al sistema aleante originó que la fase predominante fuera la austenita. Además, contribuyó a la formación de carburos de vanadio (VC) en la microestructura de la capa de relleno, sin observarse la presencia de carburos complejos. Por otra parte, la presencia de Si favoreció la formación de una red de ferrita interdendrítica. La adición de estos elementos de aleación mejoró las propiedades de estos depósitos, potencializando su uso en aplicaciones que requieren alta resistencia al desgaste bajo altas cargas.

1 January 2020 in Matéria (Rio de Janeiro)
Verified
Journal Article
Open access
PDF file
EPEdgar Ivan Pio
Edgar Ivan Pio
Pablo Martin Saint-LaurencePablo Martin Saint-Laurence
Pablo Martin Saint-Laurence
Claudio AguilarClaudio Aguilar
Claudio Aguilar
LBLuis Bejar
Luis Bejar
Ariosto MedinaAriosto Medina
Ariosto Medina
Ismeli AlfonsoIsmeli Alfonso
Ismeli Alfonso
RESUMEN Las aleaciones Ti-β se han vuelto altamente demandadas en la industria, por sus buenas características físicas y químicas. En el presente trabajo, se sintetizó una aleación Ti-13Ta-3Sn (%at) por aleado mecánico con tiempos entre 2 y 100h. Las aleaciones se caracterizaron por difracción de rayos X (DRX) y los patrones se analizaron por el método Rietveld con el software MAUD. Se caracterizaron los cambios microestructurales y la evolución de las fases Ti-α y Ti-β. Se identificó la presencia una nueva fase metaestable fcc y la síntesis de una aleación con un 79,80% en peso de fase Ti-β, ambas con tamaño de cristalita nanométrico.

1 June 2019 in Microscopy and Microanalysis
Verified
Journal Article
Closed access
PDF file
LBLuis Bejar
Luis Bejar
EHE. Huape
E. Huape
AMA. Medina
A. Medina
AMAbraham A. Mejía
Abraham A. Mejía
CAC. Aguilar
C. Aguilar
IAI. Alfonso
I. Alfonso

14 May 2015 in Revista de Metalurgia
Verified
Journal Article
Open access
Ismeli AlfonsoIsmeli Alfonso
Ismeli Alfonso
LBLuis Bejar
Luis Bejar
Ariosto MedinaAriosto Medina
Ariosto Medina
HCHECTOR CARREON
HECTOR CARREON
JSJosé Solis
José Solis