A tin oxide (SnO₂) and reduced graphene oxide (rGO) hybrid composite gas sensor for high-performance carbon dioxide (CO₂) gas detection at room temperature was studied. Since it can be used independently from a heater, it emerges as a promising candidate for reducing the complexity of device circuitry, packaging size, and fabrication cost; furthermore, it favors integration into portable devices with a low energy density battery. In this study, SnO₂-rGO was prepared via an in-situ chemical reduction route. Dedicated material characterization techniques including field emission scanning electron microscopy (FESEM), high-resolution transmission electron microscopy (HRTEM), energy dispersive X-ray (EDX) spectroscopy, Raman spectroscopy, and X-ray photoelectron spectroscopy (XPS) were conducted. The gas sensor based on the synthesized hybrid composite was successfully tested over a wide range of carbon dioxide concentrations where it exhibited excellent response magnitudes, good linearity, and low detection limit. The synergistic effect can explain the obtained hybrid gas sensor’s prominent sensing properties between SnO₂ and rGO that provide excellent charge transport capability and an abundance of sensing sites.

For decades, Metal oxide (MOX) gas sensors have been commercially available and used in various applications such as the Smart City, gas monitoring, and safety due to advantages such as high sensitivity, a high detection range, fast reaction time, and cost-effectiveness. However, several factors affect the sensing ability of MOX gas sensors. This article presents the results of a study on the cross-sensitivity of MOX gas sensors toward ambient temperature and humidity. A gas sensor array consisting of temperature and humidity sensors and four different MOX gas sensors (MiCS-5524, GM-402B, GM-502B, and MiCS-6814) was developed. The sensors were subjected to various relative gas concentrations, temperatures (from 16 °C to 30 °C), and humidity levels (from 75% to 45%), representing a typical indoor environment. The results proved that the gas sensor responses were significantly affected by the temperature and humidity. The increased temperature and humidity levels led to a decreased response for all sensors, except for MiCS-6814, which showed the opposite response. Hence, this work proposed regression models for each sensor, which can correct the gas sensor response drift caused by the ambient temperature and humidity variations. The models were validated, and the standard deviations of the corrected sensor response were found to be 1.66 kΩ, 13.17 kΩ, 29.67 kΩ, and 0.12 kΩ, respectively. These values are much smaller compared to the raw sensor response (i.e., 18.22, 24.33 kΩ, 95.18 kΩ, and 2.99 kΩ), indicating that the model provided a more stable output and minimised the drift. Overall, the results also proved that the models can be used for MOX gas sensors employed in the training process, as well as for other sets of gas sensors.

Current lifestyles promote the development and advancement in wireless technologies, especially in Wireless Sensor Networks (WSN) due to its several benefits. WSN offers a low cost, low data rate, flexible routing, longer lifetime, and low-energy consumption suitable for unmanned and long term monitoring. Among huge WSN applications, some key applications are smart houses, environmental monitoring, military applications, and other monitoring applications. As a result, ubiquitous increase in the number of wireless devices occupying the 2.4GHz frequency band. This causes a dense wireless connection followed by interference problem to WSN in the 2.4GHz frequency band. WSN is most affected by the interference issue because it has a lower data rate and transmission power compared to WLAN. Despite efforts made by researchers, to the author's knowledge, the interference issue is still a major problem in wireless networks. This paper aims to review the coexistence and interference issues of existing wireless technologies in the 2.4GHz Industrial, Scientific and Medical (ISM) band.

This paper presents a performance analysis of two open-source, laser scanner-based Simultaneous Localization and Mapping (SLAM) techniques (i.e., Gmapping and Hector SLAM) using a Microsoft Kinect to replace the laser sensor. Furthermore, the paper proposes a new system integration approach whereby a Linux virtual machine is used to run the open source SLAM algorithms. The experiments were conducted in two different environments; a small room with no features and a typical office corridor with desks and chairs. Using the data logged from real-time experiments, each SLAM technique was simulated and tested with different parameter settings. The results show that the system is able to achieve real time SLAM operation. The system implementation offers a simple and reliable way to compare the performance of Windows-based SLAM algorithm with the algorithms typically implemented in a Robot Operating System (ROS). The results also indicate that certain modifications to the default laser scanner-based parameters are able to improve the map accuracy. However, the limited field of view and range of Kinect’s depth sensor often causes the map to be inaccurate, especially in featureless areas, therefore the Kinect sensor is not a direct replacement for a laser scanner, but rather offers a feasible alternative for 2D SLAM tasks.

Gas distribution mapping (GDM) learns models of the spatial distribution of gas concentrations across 2D/3D environments, among others, for the purpose of localizing gas sources. GDM requires run-time robot positioning in order to associate measurements with locations in a global coordinate frame. Most approaches assume that the robot has perfect knowledge about its position, which does not necessarily hold in realistic scenarios. We argue that the simultaneous localization and mapping (SLAM) algorithm should be used together with GDM to allow operation in an unknown environment. This paper proposes an SLAM-GDM approach that combines Hector SLAM and Kernel DM + V through a map merging technique. We argue that Hector SLAM is suitable for the SLAM-GDM approach since it does not perform loop closure or global corrections, which in turn would require to re-compute the gas distribution map. Real-time experiments were conducted in an environment with single and multiple gas sources. The results showed that the predictions of gas source location in all trials were often correct to around 0.5–1.5 m for the large indoor area being tested. The results also verified that the proposed SLAM-GDM approach and the designed system were able to achieve real-time operation. GRAPHICAL ABSTRACT

Global path planning techniques have been widely employed in solving path planning problems, however they have been found to be unsuitable for unknown environments. Contrarily, the traditional Q-learning method, which is a common reinforcement learning approach for local path planning, is unable to complete the task for multiple targets. To address these limitations, this paper proposes a modified Q-learning method, called Vector Field Histogram based Q-learning (VFH-QL) utilized the VFH information in state space representation and reward function, based on a 2D LiDAR sensor. We compared the performance of our proposed method with the classical Q-learning method (CQL) through training experiments that were conducted in a simulated environment with a size of 400 square pixels, representing a 20-meter square map. The environment contained static obstacles and a single mobile robot. Two experiments were conducted: experiment A involved path planning for a single target, while experiment B involved path planning for multiple targets. The results of experiment A showed that VFH-QL method had 87.06% less training time and 99.98% better obstacle avoidance compared to CQL. In experiment B, VFH-QL method was found to have an average training time that was 95.69% less than that of the CQL method and 83.99% better path quality. The VFH-QL method was then evaluated using a benchmark dataset. The results indicated that the VFH-QL exhibited superior path quality, with efficiency of 94.89% and improvements of 96.91% and 96.69% over CQL and SARSA in the task of path planning for multiple targets in unknown environments.