In the tire industry, the combination of carbon black and silica is commonly utilized to improve the comprehensive performance of natural rubber so as to realize the best performance and cost-effectiveness. The corresponding mixing is divided into three processes (initial mixing, delivery, reactive mixing) by the serial modular continuous mixing method, thus achieving more accurate control of the mixing process, higher production efficiency and better performance. Moreover, the optimization of serial modular continuous mixing process parameters can not only improve the performance of composite materials, but help people understand the physical and chemical changes and the reinforcing mechanism of fillers in the mixing process. In this paper, the relationship among the parameters of eight processes and filler network structure, tensile strength, chemical reinforcing effect and tear resistance was explored through experiments. The deep causes of performance changes caused by parameters were analyzed. Consequently, the best process condition and the ranking of the influencing factors for a certain performance was obtained. Furthermore, the best preparation process of natural rubber (NR)/carbon black/silica composite was achieved through comprehensive analysis.

In order to efficiently prepare high-performance silica/rubber composites for use in the tread of semi-steel radial tires, a serial modular continuous mixer was designed according to the principle of modular functionalization. The modular structure and serial process helped control the accuracy of the silanization reaction. Synchronous four-wing serrated rotors and reverse meshing reaction mixing twin-rotors utilized shear flow and elongation flow to improve the dispersion. In this paper, the mechanism of serial modular continuous mixing was analyzed, and the influence of the core reaction mixing zone (various mixing elements) on silica-filled compounds was investigated by cooling visualization experiments, including dispersion, and the silanization reaction degree. Meanwhile, a comparative experiment between serial mixing and two-stage mixing was conducted, which showed that the serial process comprehensively improved the dispersion, mechanical properties, and dynamic mechanical properties of silica/rubber vulcanizate.

Research on the synergistic high-value reuse of waste tires and used catalysts in spent fluid catalytic cracking (FCC) catalysts was carried out in this study to address the serious ecological and environmental problems caused by waste tires and spent FCC catalysts. The experiment, in which a spent FCC catalyst was applied to the catalytic cracking of waste tires, fully utilized the residual activity of the spent FCC catalyst and was compared with a waste tire pyrolysis experiment. The comparative experimental results indicated that the spent FCC catalyst could improve the cracking efficiency of waste tires, increase the output of light oil in pyrolysis products, and improve the quality of pyrolysis oil. It could also be used for the conversion of sulfur compounds during cracking. The content of 2-methyl-1-propylene in catalytic cracking gas was found to be up to 65.59%, so a new method for producing high-value chemical raw materials by the catalytic cracking of waste tires with spent FCC catalysts is proposed.

Due to the widespread production and use of carbon nanotubes in almost every area of science (i.e., drug delivery, biosensors, fuel cells and thermal management systems), they are receiving considerable attention for their novel mechanical, electrical and chemical properties. At this time of high exposure potential, it is critical to ascertain the biological impact of these materials on likely target organs, tissues and cells, such as those of the lung. The aim of this study was to evaluate the degree of cytotoxicity to human lung macrophage (U937) cells after exposure to unpurified or acid-purified multi-walled carbon nanotubes. Cells were incubated with multi-walled carbon nanotubes and assessed for cytotoxicity, generation of reactive oxygen species, morphological changes and uptake. The results demonstrate that multi-walled carbon nanotubes can accumulate in human lung macrophage cells to different degrees based on their surface chemistry. MWNT-COOH reduces cell viability in a dose-dependent manner under these experimental conditions (5–50 g/ml, 2–24 h). However, images of individual cells demonstrate morphological changes at low concentrations. Therefore, before nanomaterials are fully accepted and integrated into biological systems, they will continue to undergo further scrutiny at various stages of their processing (i.e., before and after purification) and with models ranging from simple to complex (i.e., cells vs. whole animals) to gain a better understanding between their physicochemical properties and bio-effects.

In order to obtain a longer mixing chamber life, a layer of hard alloy coating is generally welded on the surface. However, when the mixing chamber is used for a long time, the surface will be worn due to friction with small fillers and rubber. As a result, there will be a large gap between the mixing chamber and the rotor, which will further affect the quality of the mixed rubber. In this paper, the dispersion process of the reinforcing system is simulated at first, and the mixed rubber samples are obtained from different dispersion stages in preparation for experiments with the chamber material. On this basis, the friction experiment is carried out with the same material as the mixing chamber on the friction experiment machine employed in the improved test part. The experiment shows that the friction and wear between the mixture and metal produced in each mixing stage are different. The wear in the stage with high friction is not necessarily large. The wear will be intensified in the middle and later mixing periods, while the friction will tend to be stable. In this paper, besides the exploration on the friction of fillers and rubber on the mixing chamber in different mixing stages, the most important thing is to change the mixing process of rubber formula, so as to extend the service life of the mixing chamber without changing the comprehensive physical properties of the mixing rubber.