Reducing aerodynamic drag in automobiles has been one of the focuses in automotive industry as it will increase vehicles performance and reduce power consumption which subsequently save the environment. Drag is a force that tend to pull the vehicle backwards. Pressure drag is the major contributor to drag of vehicle which caused by lower pressure in the rear area compared to front of vehicle. When vehicle moves forward, the stagnation point occurs in the front part of vehicle. The airflow then goes over the vehicle and separate at the back due to adverse pressure gradient. Thus, flow separation is created in the rear area of vehicle as indicated by the wake. Wake is a low-pressure region that need to be reduced so that the pressure between the front and rear could be reduced to minimize the drag. Flow control is introduced to delay this flow separation and it has been categorized as active and passive. Active flow controls require power input while passive flow controls do not need power input. This review article will explore those studies on flow controls applied in automobiles and investigate their working mechanisms along with research gaps detected. Relative comparison of effectiveness for each flow control is unfeasible as the parameters used differs but this problem can be resolved. Standard parameters need to be used in future researches in order address the discrepancy of results obtained from numerous studies around the globe. A current flow control technique is proposed to be conducted in UTM Aerolab to further investigate this interesting flow field.
6 July 2022 in Journal of Advanced Research in Fluid Mechanics and Thermal Sciences
The purpose of this study is to see the feasibility of using Computational Fluid Dynamic (CFD) analysis over wind tunnel testing for propeller performance measurement. Computational Fluid Dynamic (CFD) analysis is conducted on APC 6X4E propeller and 9X6E propeller at propeller disc angle, α of 0°, 30°, 60°, and 90° using commercially available software ANSYS FLUENT at advance ratio ranging from 0 to 0.88 and angular velocity ranging from 1000rpm to 8000rpm. CFD analysis was also performed for different advance ratio at different rotational speed of 4000rpm and 8000rpm. Multiple Reference Frame model is used to simulate the rotating propeller in a flowing airstream by constructing a rotating and static domain around the propeller. The non-zero propeller disc angle is achieved by changing the inlet direction of the static domain. The SST k-ω turbulence model is used, and tetrahedral mesh is constructed. The propeller thrust and torque obtained from the CFD simulation is used to calculate the aerodynamic characteristics of the propellers. The thrust coefficient, torque coefficient and propeller efficiency obtained for both propellers follow the trend of the wind tunnel testing. The results obtained from the CFD simulation matches with the results trend obtained by another researcher performing wind tunnel analysis, where the thrust coefficient decreases with increasing advance ratio at propeller disc angle less than 60° and increases with increasing advance ratio at propeller disc angle more than 70°. The error produce for thrust estimation is lower than 12% for both 6x4E and 9x6E propellers. The error for torque and efficiency estimation is between 15-30% and 12% respectively. In conclusion, CFD simulation can predict the aerodynamic characteristics of Low Reynolds Number propeller at different propeller disc angle.
The purpose of developing the magnetically-levitated solar motor is to investigate and evaluate the performance of the solar motor in terms of its efficiency. M The purpose of developing the magnetically-levitated solar motor is to investigate and evaluate the performance of the solar motor in terms of its efficiency. M
30 October 2023 in Journal of Transport System Engineering
In the world of Unmanned Aircraft Vehicle, controls and stability are important to ensure a safe flight mission. As UAVs are an aircraft that operates dependently to the reference trajectory given, a reliable system and controller are in need for the UAV to carry through flight missions safely. This research focusses on the design of a cascaded PID controller to control the UAV to follow climb, cruise, and landing trajectory. The designed PID is tested to see the system robustness when influenced by wind disturbances. The response of flight under influence of wind is acceptable, however, the controller does not satisfy the system’s flying quality at a wind disturbance exceeding step input of 1-70 km/h and 1-100 km/h or above due to the size of the UAV. The acceptable response are accounted for final gains of kpq≈0, kiq≈0, kdq=-0.00034, kpθ=-0.5116, kiθ=-0.002267, kdθ=0, kph=13.3931, kih=1.01882 and kdh=13.9178 in order to achieve such results.
18 October 2024 in Journal of Advanced Research in Applied Sciences and Engineering Technology
Sign language is the main form of communication used by deaf people. Most of their activities like speaking and learning involved sign language. In Malaysia, instead of a deaf person, only a few people know sign language because it's not part of the co-curriculum. Hence, normal people need to know sign language so that they can communicate with deaf people effectively. However, learning sign language requires a lot of effort and takes years of study. Therefore, this research tends to initiate the sign language image detection system that utilizes the deep learning model. The initial effort involves the development of an image detection system that can identify the alphabet of sign language from A to Z. There will be 26 alphabets that contribute to 26 classes of image detection using the Convolutional Neural Network. 85 images will be collected for each alphabet and the total data will be distributed into 80% and 20% for training and testing the CNN model, respectively. The result showed that the proposed system produced more than 95% detection accuracy of the alphabet based on finger sign gestures. For future works, the proposed system will be evaluated with a more complex dataset in terms of words.