Shabudin Mat

Shabudin Mat

Auto-generated profile, based on publicly available information

Shabudin Mat

Universiti Teknologi Malaysia

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
21 September 2022 in Energies
Verified
Journal Article
Open access
PDF file
SUShern-Khai Ung
Shern-Khai Ung
Chong Wen TongChong Wen Tong
Chong Wen Tong
SMShabudin Mat
Shabudin Mat
Jo-Han NgJo-Han Ng
Jo-Han Ng
YKYin-Hui Kok
Yin-Hui Kok
Kok Hoe WongKok Hoe Wong
Kok Hoe Wong
For the past decade, research on vertical axis wind turbines (VAWTs) has garnered immense interest due to their omnidirectional characteristic, especially the lift-type VAWT. The H-rotor Darrieus VAWT operates based on the lift generated by aerofoil blades and typically possesses higher efficiency than the drag-type Savonius VAWT. However, the open-ended blades generate tip loss effects that reduce the power output. Wingtip devices such as winglets and endplates are commonly used in aerofoil design to increase performance by reducing tip losses. In this study, a CFD simulation is conducted using the sliding mesh method and the k-ω SST turbulence model on a two-bladed NACA0018 VAWT. The aerodynamic performance of a VAWT with offset, symmetric V, asymmetric and triangular endplates are presented and compared against the baseline turbine. The simulation was first validated with the wind tunnel experimental data published in the literature. The simulation showed that the endplates reduced the swirling vortex and improved the pressure distribution along the blade span, especially at the blade tip. The relationship between TSR regimes and the tip loss effect is also reported in the paper. Increasing VAWT performance by using endplates to minimise tip loss is a simple yet effective solution. However, the improvement of the power coefficient is not remarkable as the power degradation only involves a small section of the blades.

18 January 2023 in Journal of Advanced Research in Fluid Mechanics and Thermal Sciences
Verified
Journal Article
Open access
PDF file
RMRafiqi Daniel Ramadhan Mariaprakasam
Rafiqi Daniel Ramadhan Mariaprakasam
SMShabudin Mat
Shabudin Mat
PSPakharuddin Mohd Samin
Pakharuddin Mohd Samin
NONorazila Othman
Norazila Othman
MWMastura Ab Wahid
Mastura Ab Wahid
MSMazuriah Said
Mazuriah Said
Reducing aerodynamic drag in automobiles has been one of the focuses in automotive industry as it will increase vehicles performance and reduce power consumption which subsequently save the environment. Drag is a force that tend to pull the vehicle backwards. Pressure drag is the major contributor to drag of vehicle which caused by lower pressure in the rear area compared to front of vehicle. When vehicle moves forward, the stagnation point occurs in the front part of vehicle. The airflow then goes over the vehicle and separate at the back due to adverse pressure gradient. Thus, flow separation is created in the rear area of vehicle as indicated by the wake. Wake is a low-pressure region that need to be reduced so that the pressure between the front and rear could be reduced to minimize the drag. Flow control is introduced to delay this flow separation and it has been categorized as active and passive. Active flow controls require power input while passive flow controls do not need power input. This review article will explore those studies on flow controls applied in automobiles and investigate their working mechanisms along with research gaps detected. Relative comparison of effectiveness for each flow control is unfeasible as the parameters used differs but this problem can be resolved. Standard parameters need to be used in future researches in order address the discrepancy of results obtained from numerous studies around the globe. A current flow control technique is proposed to be conducted in UTM Aerolab to further investigate this interesting flow field.

6 July 2022 in Journal of Advanced Research in Fluid Mechanics and Thermal Sciences
Verified
Journal Article
Open access
PDF file
LHLeong Chee Hang
Leong Chee Hang
NRNur Athirah Nadwa Rosli
Nur Athirah Nadwa Rosli
MWMastura Ab Wahid
Mastura Ab Wahid
NONorazila Othman
Norazila Othman
SMShabudin Mat
Shabudin Mat
MZMohd Zarhamdy Md. Zain
Mohd Zarhamdy Md. Zain
The purpose of this study is to see the feasibility of using Computational Fluid Dynamic (CFD) analysis over wind tunnel testing for propeller performance measurement. Computational Fluid Dynamic (CFD) analysis is conducted on APC 6X4E propeller and 9X6E propeller at propeller disc angle, α of 0°, 30°, 60°, and 90° using commercially available software ANSYS FLUENT at advance ratio ranging from 0 to 0.88 and angular velocity ranging from 1000rpm to 8000rpm. CFD analysis was also performed for different advance ratio at different rotational speed of 4000rpm and 8000rpm. Multiple Reference Frame model is used to simulate the rotating propeller in a flowing airstream by constructing a rotating and static domain around the propeller. The non-zero propeller disc angle is achieved by changing the inlet direction of the static domain. The SST k-ω turbulence model is used, and tetrahedral mesh is constructed. The propeller thrust and torque obtained from the CFD simulation is used to calculate the aerodynamic characteristics of the propellers. The thrust coefficient, torque coefficient and propeller efficiency obtained for both propellers follow the trend of the wind tunnel testing. The results obtained from the CFD simulation matches with the results trend obtained by another researcher performing wind tunnel analysis, where the thrust coefficient decreases with increasing advance ratio at propeller disc angle less than 60° and increases with increasing advance ratio at propeller disc angle more than 70°. The error produce for thrust estimation is lower than 12% for both 6x4E and 9x6E propellers. The error for torque and efficiency estimation is between 15-30% and 12% respectively. In conclusion, CFD simulation can predict the aerodynamic characteristics of Low Reynolds Number propeller at different propeller disc angle.

15 December 2025 in Energies
Verified
Journal Article
Open access
PDF file
XWXiao Hang Wang
Xiao Hang Wang
CKChong Shen Khor
Chong Shen Khor
Kok Hoe WongKok Hoe Wong
Kok Hoe Wong
JNJing Hong Ng
Jing Hong Ng
SMShabudin Mat
Shabudin Mat
Chong Wen TongChong Wen Tong
Chong Wen Tong
Wind power is a major source of renewable energy, yet turbine performance is strongly influenced by atmospheric conditions and surrounding terrain. Several meteorological phenomena can hinder energy production, disrupt operations, and accelerate structural deterioration. This paper reviews three key atmospheric hazards affecting wind turbine systems: lightning, icing, and rain. For each phenomenon, the formation mechanisms, operational effects, and mitigation approaches are examined, with offshore-specific processes and conditions integrated directly into each hazard discussion. Building on this foundation, the review then analyses interactions between the hazards, their combined implications for turbine performance and maintenance, and the associated economic impacts. Comparisons of material behaviour across lightning, icing, and rain-erosion conditions are also incorporated. Finally, future research directions are proposed.

30 October 2016 in IOP Conference Series: Materials Science and Engineering
Verified
Conference Paper
Open access
PDF file
MUM I Ujang
M I Ujang
SMS Mat
S Mat
KPK Perumal
K Perumal
MNM N Mohd. Nasir
M N Mohd. Nasir
This paper presents the experimental results from the investigation carried out at the UTM Low Speed wind tunnel facility (UTM-LST) on a half model generic transport aircraft at several configurations of primary control surfaces (flap, aileron and elevator). The objective is to measure the aerodynamic forces and moments due to the configuration changes. The study is carried out at two different speeds of 26.1 m/s and 43.1 m/s at corresponding Reynolds number of 1 × 106 and 2 × 106, respectively. Angle of attack of the model is varied between -2o to 20o. For the flaps, the deflection applied is 0o, 5o and 10o. Meanwhile, for aileron and elevator, the deflection applied is between -10o and 10o. The results show the differences in aerodynamic characteristics of the aircraft at different control surfaces configurations. The results obtained indicate that a laminar separation bubble developed on the surface of the wing at lower angles of attack and show that the separation process is delayed when the Reynolds number is increased.

21 July 2023 in International Journal of Aerospace Engineering
Verified
Journal Article
Open access
PDF file
IMIbrahim Madan
Ibrahim Madan
JMJiun-Jih Miau
Jiun-Jih Miau
SMShabudin Bin Mat
Shabudin Bin Mat
This paper highlights the results and comparison of the flow topology investigation above the unmanned combat aerial vehicle (UCAV) configuration, namely, multidisciplinary design configuration (MULDICON), with modified leading-edge profile at the apex region from a sharp to a blunt profile to reduce the complexity of the flow structure above the wing. It was found from the flow visualization results that at a low angle of attack, for instance, 10°, the onset of the flow separation took place near the apex region; the onset of a tip vortex at the wing tip was also detected. At a medium angle of attack, for instance, 15°, the onset of the flow separation moved further upstream with the formation of the apex vortex, and the magnitude of the tip vortex increased due to increasing incoming flow with increasing the angle of attack. At higher angle of attack, for instance, 20°, the apex vortex intensity increased and wing tip vortices shedding is observed. Furthermore, at an angle of attack of 25°, the configuration is partially stalled, while a complete stalled occurred at an angle of attack of 30°. The current results obtained from this study have shown that the configuration has a maximum lift coefficient of 0.8 obtained from the K-Omega-SST turbulence model while it is 0.93 calculated from the Spalart-Allmaras turbulence model, while the maximum drag coefficient is 0.31 and 0.35, respectively, when calculated for the K-Omega-SST turbulence model and the Spalart-Allmaras turbulence model at an AOA of 25°. The flow visualization results revealed that there is a single flow separation due to modified leading edge from sharp to blunt, thus flow complexity is reduced.