The thermal stability of nanostructured microstructures consisting of a mixture of bainitic ferrite and carbon-enriched retained austenite has been studied in two steels containing 0.6 C (wt %) by tempering cycles of 1 h at temperatures ranging from 450 to 650 °C. Volume changes due to microstructural transformations during thermal treatments were measured by high-resolution dilatometry. The correlation of these results with the detailed microstructural characterization performed by X-ray diffraction and scanning electron microscope examination showed a sequence of different decomposition events beginning with the precipitation of very fine cementite particles. This precipitation, which starts in the austenite thin films and then continues in retained austenite blocks, decreases the carbon content in this phase so that fresh martensite can form from the low-carbon austenite on cooling to room temperature. In a subsequent tempering stage, the remaining austenite decomposes into ferrite and cementite, and due to carbide precipitation, the bainitic ferrite loses its tetragonality, its dislocation density is reduced, and the bainitic laths coarsen.
Bainitic ferrite plate thickness evolution during isothermal transformation was followed at the same holding temperatures in two nanostructured steels containing (in wt.%) 1C-2Si and 0.4C-3Si. A dynamic picture of how the bainitic transformation evolves was obtained from the characterization of the microstructure present at room temperature after full and partial transformation at 300 and 350 °C. The continuous change during transformation of relevant parameters influencing the final scale of the microstructure, YS of austenite, driving force of the transformation and evolution of the transformation rate has been tracked, and these variations have been correlated to the evolution of the bainitic ferrite plate. Instead of the expected refinement of the plate predicted by existing theory and models, this study revealed a thickening of the bainitic ferrite plate thickness as the transformation progresses, which is partially explained by changes in the transformation rate through the whole decomposition of austenite into bainitic ferrite.
Low temperature bainite consists of an intimate mixture of bainitic ferrite and retained austenite, usually obtained by isothermal treatments at temperatures close to the martensite start temperature and below the bainite start temperature. There is widespread belief regarding the extremely long heat treatments necessary to achieve such a microstructure, but still there are no unified and objective criteria to determine the end of the bainitic transformation that allow for meaningful results and its comparison. A very common way to track such a transformation is by means of a high-resolution dilatometer. The relative change in length associated with the bainitic transformation has a very characteristic sigmoidal shape, with low transformation rates at the beginning and at end of the transformation but rapid in between. The determination of the end of transformation is normally subjected to the ability and experience of the “operator” and is therefore subjective. What is more, in the case of very long heat treatments, like those needed for low temperature bainite (from hours to days), differences in the criteria used to determine the end of transformation might lead to differences that might not be assumable from an industrial point of view. This work reviews some of the most common procedures and attempts to establish a general criterion to determine the end of bainitic transformation, based on the differential change in length (transformation rate) derived from a single experiment. The proposed method has been validated by means of the complementary use of hardness measurements, X-ray diffraction and in situ high energy X-ray diffraction.
1 November 2020 in Archives of Civil and Mechanical Engineering
The work addresses physical simulation and dilatometric study of one-step and double-step heat treatments of medium-Mn steel designed for automotive sheets. The conventional one-step isothermal bainitic transformation was applied as the reference heat treatment. The newly implemented heat treatment consisted of isothermal holding in a bainitic region followed by additional holding of the material at reduced temperature also in the bainitic range. This step was added to refine the microstructure, which led to the stabilization of the retained austenite. Calculations of equilibrium state and non-equilibrium cooling and simulations of the developed thermal cycles were performed using the thermodynamic JMatPro software. The physical simulations of the heat treatment were performed in the dilatometer. The obtained samples were subjected to microscopic observations using light and SEM microscopy. One- and two-step heat treatments allowed to obtain bainitic structures with high contents of retained austenite. Lowering the temperature of one-step isothermal holding resulted in the bainite refinement and adjacent retained austenite. The increased Mn content in steel increased its susceptibility to form coalesced bainite resulting in the partial formation of thicker plates despite a decrease in a process temperature.