The vehicle suspension system is one of the main design factors in the automobile industry that can exponentially increase the level of customers comport and satisfaction. Various design strategies can be used to get optimum values for the various parameters in the suspension system. In this paper, a passive vehicle suspension system was modeled, and the system was optimized using Genetic Algorithm (GA) optimization technique. The GA is based on natural evolution and is successfully applied to various real-world problems. The variance of the dynamic load resulting from the vibrating vehicle is taken as the performance measure (i.e., objective function) of the suspension system. During the application of GA, first appropriate mutation rate, crossover rate, and population size were evaluated which were used to calculate optimum values for the parameters in the suspension system. The optimum values for the suspension system correspond to minimum values of the settling time and maximum overshoot and thus helps in decreasing the effect of the dynamic loads by reducing the vehicle vibration.
Thermoacoustic refrigerators have huge potential to replace conventional refrigeration systems as an alternative clean refrigeration technology. These devices utilize conversion of acoustic power and heat energy to generate the desired cooling. The stack plays a pivotal role in the performance of Standing Wave Thermoacoustic Refrigerators (SWTARs), as the heat transfer takes place across it. Performance of stacks can be significantly improved by making an arrangement of different materials inside the stack, resulting in anisotropic thermal properties along the length. In the present numerical study, the effect of multi-layered stack on the refrigeration performance of a SWTAR has been evaluated in terms of temperature drop across the stack, acoustic power consumed and device Coefficient of Performance (COP). Two different aspects of multi-layered stack, namely, different material combinations and different lengths of stacked layers, have been investigated. The combinations of four stack materials and length ratios have been investigated. The numerical results showed that multi-layered stacks produce lower refrigeration temperatures, consume less energy and have higher COP value than their homogeneous counterparts. Among all the material combinations of multi-layered stack investigated, stacks composed of a material layer with low thermal conductivity at the ends, i.e., RVC, produced the best performance with an increase of 26.14% in temperature drop value, reduction in the acoustic power consumption by 4.55% and COP enhancement of 5.12%. The results also showed that, for a constant overall length, an increase in length of side stacked material layer results in an increase in values of both temperature drop and COP.
Simulation driven designs are used for the efficient development of high precision devices such as parallel manipulators/platforms. Accurate prediction of these simulations depends upon the fact that how closely actual conditions are incorporated in the analysis. Stiffness is a key property for parallel platforms as it dictates the positional accuracy of the system. Overall stiffness of the platforms is not only driven by the stiffness of the links but also by contact stiffness of joints. Heavily loaded platforms present a special case as these are more prone to system failure if not designed properly. In this work, the stiffness behavior of 6-DOF platform's top plate subjected to various boundary conditions at joints have been analyzed. Different boundary conditions i.e. volume at joints, surface at joints and line at joints, has been used to depict real joint behavior. The stiffness of platform is analyzed for each of these cases independently and comparison of simulation results for every condition is presented both for static as well as dynamic conditions. This comparison presents a useful outcome for better prediction of static stiffness behavior and dynamic response thus aiding in more accurate design of such applications.
15 March 2020 in International Journal of Simulation Modelling
Sensitivity analysis using normalized sensitivity coefficient (NSC) can be used to identify important model parameters affecting the device performance by allowing one to one comparison. The results are highlighted in the form of order of magnitudes change in output for a unit change in the input variable. In this work, sensitivity analysis of a small capacity standing wave thermoacoustic refrigerator (SWTAR) has been performed using NSC. Specialized tool DeltaEC has been used to generate the results for subsequent sensitivity analysis. Three key performance parameters i.e. temperature difference achieved (ΔT), coefficient of performance (COP) and relative coefficient of performance (COPR) have been analyzed for perturbations in number of device variables, namely oscillating pressure amplitude, two different stack material properties and four stack geometric parameters i.e. stack length, stack center position, stack plate thickness and half stack spacing. Sensitivity results are obtained for a wide range of mean operating pressures (Pm), mean operating temperature (Tm) and drive ratios (DR). It has been found that performance parameters are most sensitive to the perturbations in oscillating pressure amplitude and least affected by the perturbations in stack length. With respect to oscillating pressure amplitude, maximum NSC of 24.12 has been reported for ΔT at mean pressure of 5 bar.