Sergey Generalov

Sergey Generalov


Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
2 November 2021 in Sensors
Verified
Journal Article
Open access
PDF file
MAMatvey Andreev
Matvey Andreev
VPVadim Platonov
Vadim Platonov
DFDarya Filatova
Darya Filatova
EGElena Galitskaya
Elena Galitskaya
SPSergey Polomoshnov
Sergey Polomoshnov
Marina RumyantsevaMarina Rumyantseva
Marina Rumyantseva
Continuous monitoring of greenhouse gases with high spatio-temporal resolution has lately become an urgent task because of tightening environmental restrictions. It may be addressed with an economically efficient solution, based on semiconductor metal oxide gas sensors. In the present work, CO2 detection in the relevant concentration range and ambient conditions was successfully effectuated by fine-particulate La2O3-based materials. Flame spray pyrolysis technique was used for the synthesis of sensitive materials, which were studied with X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FTIR), diffuse reflectance infrared Fourier transform spectroscopy (DRIFTs) and low temperature nitrogen adsorption coupled with Brunauer–Emmett–Teller (BET) effective surface area calculation methodology. The obtained materials represent a composite of lanthanum oxide, hydroxide and carbonate phases. The positive correlation has been established between the carbonate content in the as prepared materials and their sensor response towards CO2. Small dimensional planar MEMS micro-hotplates with low energy consumption were used for gas sensor fabrication through inkjet printing. The sensors showed highly selective CO2 detection in the range of 200–6667 ppm in humid air compared with pollutant gases (H2 50 ppm, CH4 100 ppm, NO2 1 ppm, NO 1 ppm, NH3 20 ppm, H2S 1 ppm, SO2 1 ppm), typical for the atmospheric air of urbanized and industrial area.

7 November 2020 in Photonics
Verified
Journal Article
Open access
PDF file
AYAnastasiya Yakuhina
Anastasiya Yakuhina
AKAleksei S. Kadochkin
Aleksei S. Kadochkin
VSVyacheslav Svetukhin
Vyacheslav Svetukhin
DGDmitry Gorelov
Dmitry Gorelov
SGSergey Generalov
Sergey Generalov
VAVladimir Amelichev
Vladimir Amelichev
This article presents the results of the study of the influence of the most significant parameters of the side wall roughness of an ultra-thin silicon nitride lightguide layer of multimode integrated optical waveguides with widths of 3 and 8 microns. The choice of the waveguide width was made due to the need to provide multimode operation for telecommunication wavelengths, which is necessary to ensure high integration density. Scattering in waveguide structures was measured by optical frequency domain reflectometry (OFDR) of a backscattering reflectometer. The finite difference time domain method (FDTD) was used to study the effect of roughness parameters on optical losses in fabricated waveguides, the roughness parameters that most strongly affect optical scattering were determined, and methods of its significant reduction were specified. The prospects for implementing such structures on a quartz substrate are justified.

17 June 2021 in Photonics
Verified
Journal Article
Open access
PDF file
AYAnastasiya Yakuhina
Anastasiya Yakuhina
AKAleksei S. Kadochkin
Aleksei S. Kadochkin
DGDmitry V. Gorelov
Dmitry V. Gorelov
VSVyacheslav Svetukhin
Vyacheslav Svetukhin
SGSergey Generalov
Sergey Generalov
VAVladimir Amelichev
Vladimir Amelichev
This article presents a silicon disk resonator of the whispering-gallery-mode (WGM) type. The calculated Q-factor of the silicon WGM resonator was 107. Two methods of studying the surface roughness of a silicon WGM resonator with a nonlinear profile by means of Helios 650 scanning electron microscope and Bruker atomic force microscope (AFM) are presented. The results obtained by the two methods agreed well with each other. A comparison of the surface roughness values of WGM resonators manufactured using different technological approaches is presented. Based on the obtained data, a preliminary estimated Q-factor calculation of the resonators was performed, which was refined by numerical calculation using the finite-difference time-domain (FDTD) method. The effect of the surface roughness of the resonator on its Q-factor was found. Reducing the surface roughness of the resonator from 30 nm to 1–2 nm led to an increase in its Q-factor from 104 to 107.

22 April 2020 in Photonics
Verified
Journal Article
Open access
PDF file
AYAnastasiya Yakuhina
Anastasiya Yakuhina
AKAleksei S. Kadochkin
Aleksei S. Kadochkin
VAVladimir Amelichev
Vladimir Amelichev
DGDmitry Gorelov
Dmitry Gorelov
SGSergey Generalov
Sergey Generalov
This article presents the results of a computer simulation of whispering gallery modes in the structure of a silicon disk resonator with a wedge-shaped profile made on a silicon-on-isolator base (SOI). The rationale for the choice of silicon as a material for its manufacturing is given. The results of the study of the influence of the wedge angle on the whispering gallery mode parameters (WGM) are presented. The optimum wedge angle of a silicon disk resonator is determined, which ensures the minimum loss and maximum mode stability. The technological aspects of plasma-chemical etching processes for forming a wedge-shaped profile of the edge of a silicon disk resonator are studied.