Continuous monitoring of greenhouse gases with high spatio-temporal resolution has lately become an urgent task because of tightening environmental restrictions. It may be addressed with an economically efficient solution, based on semiconductor metal oxide gas sensors. In the present work, CO2 detection in the relevant concentration range and ambient conditions was successfully effectuated by fine-particulate La2O3-based materials. Flame spray pyrolysis technique was used for the synthesis of sensitive materials, which were studied with X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FTIR), diffuse reflectance infrared Fourier transform spectroscopy (DRIFTs) and low temperature nitrogen adsorption coupled with Brunauer–Emmett–Teller (BET) effective surface area calculation methodology. The obtained materials represent a composite of lanthanum oxide, hydroxide and carbonate phases. The positive correlation has been established between the carbonate content in the as prepared materials and their sensor response towards CO2. Small dimensional planar MEMS micro-hotplates with low energy consumption were used for gas sensor fabrication through inkjet printing. The sensors showed highly selective CO2 detection in the range of 200–6667 ppm in humid air compared with pollutant gases (H2 50 ppm, CH4 100 ppm, NO2 1 ppm, NO 1 ppm, NH3 20 ppm, H2S 1 ppm, SO2 1 ppm), typical for the atmospheric air of urbanized and industrial area.
This article presents the results of the study of the influence of the most significant parameters of the side wall roughness of an ultra-thin silicon nitride lightguide layer of multimode integrated optical waveguides with widths of 3 and 8 microns. The choice of the waveguide width was made due to the need to provide multimode operation for telecommunication wavelengths, which is necessary to ensure high integration density. Scattering in waveguide structures was measured by optical frequency domain reflectometry (OFDR) of a backscattering reflectometer. The finite difference time domain method (FDTD) was used to study the effect of roughness parameters on optical losses in fabricated waveguides, the roughness parameters that most strongly affect optical scattering were determined, and methods of its significant reduction were specified. The prospects for implementing such structures on a quartz substrate are justified.
A flame spray pyrolysis (FSP) technique was applied to obtain pure and Nb(V)-doped nanocrystalline β-Ga2O3, which were further studied as gas sensor materials. The obtained samples were characterized with XRD, XPS, TEM, Raman spectroscopy and BET method. Formation of GaNbO4 phase is observed at high annealing temperatures. Transition of Ga(III) into Ga(I) state during Nb(V) doping prevents donor charge carriers generation and hinders considerable improvement of electrical and gas sensor properties of β-Ga2O3. Superior gas sensor performance of obtained ultrafine materials at lower operating temperatures compared to previously reported thin film Ga2O3 materials is shown.
Spin-dependent tunneling structures are widely used in many spintronic devices and sensors. This paper describes the magnetic tunnel junction (MTJ) characteristics caused by the inhomogeneous magnetic field of ferromagnetic layers. The extremely oblate magnetic ellipsoids have been used to mimic these layers. The strong effect of an inhomogeneous magnetic field on the magnetoresistive layers’ interaction was demonstrated. The magnetostatic coupling coefficient is also calculated.
The article presents the results of experimental studies of multilayer nanostructures of magnetic straintronics formed by magnetron sputtering on a 100 mm silicon wafer. The object of the study is two types of nanostructures: Ta/FeNiCo/CoFe/Ta and Ta/FeNi/CoFe/Ta, differing in the ratio of magnetic layers. The magnetic and magnetoresistive characteristics of multilayer nanostructures under varying mechanical loads are studied both on a 100 mm wafer and in the form of 4 × 20 mm2 samples of two types. The first, where the axis of easy magnetization is directed along the long side of the sample, and the second, where the axis of easy magnetization is a tilt at 45°. Based on the obtained data, the conclusions about the practical application of these nanostructures in magnetic straintronics elements are drawn.
The influence of a magnetic field directed orthogonal to the easy magnetization axis (EMA) of an elliptical spin-tunnel junction based on the Ta/CoFe/CoFeB/MgO/CoFeB/Ru/CoFe/FeMn/Ta structure on the dependence of the spin-tunnel junction (STJ) resistance on the external magnetic field is considered. This dependence is calculated using the model of coherent rotation of the magnetization of the free layer. The calculation results are comparable with the experimental studies and can be used to simulate the design of magnetic field transducers based on spin-tunnel magnetoresistive nanostructures.