The dynamic properties and thermal history of Fe40Al at.% intermetallic particles have been estimated. The parameters of the gas detonation process for the investigated mixture have been calculated using thermochemical code, and the motion parameters as well as thermal history of the analyzed powder particles have been assessed using computational fluid dynamics software and self-developed algorithms. The appropriate models allowed for determination of the melted volume (mass) fraction of a certain analyzed single particle, which is dependent on a particle diameter ranging from 10 to 160 μm. The results show that only particles with a diameter lower than 80 μm melt under the investigated conditions. Moreover, the estimated radial distribution of the temperature inside the particle is almost homogenous due to relatively high FeAl thermal conductivity and relatively low thermal conductance of the surface heat transfer. The calculated final velocity of particles has been referred to some experimental and literature data from previous studies by other researchers, and the results were found to be in agreement.

The formation of craters is an important issue in the investigations of the surface of the earth and other planets. The aim of the study was to check whether the different textures of sand beds affect the size and dynamics of the formation of craters and ejection curtain after high-velocity impacts. The experiments were conducted using an aluminium impactor at two impact speeds (~700 and ~1300 m∙s^-1) and a sand bed composed of either a broad range of sizes (<2.0 mm) or any of the three fractions obtained from it (<0.5, 0.5–1, 1–2 mm). The diameters, depths, wall slope, and rim heights of the resulting craters were measured. The ejecta curtain was characterized by the inclination angle of walls, base diameter, and expansion velocity. The mass of the transferred material and the depth of the impactor penetration were also determined. Additionally, the results were used to calculate dimensionless parameters commonly considered in crater studies (π_V, π₂ and α). The texture of the sand most clearly influenced the diameters of the craters, its effect could also be seen in the case of the distance covered by the ejected material. This information appears to be relevant for future research, providing some rationale to help assess in which aspects of the phenomenon the texture may be important.

Numerical and experimental investigations of armament systems are an important part of modern design processes. The presented paper reports problems that were encountered on the theoretical analysis of the performance of 35 mm anti-aircraft cannon and the way in which they were solved. The first problem concerns the application of results of closed vessel tests of used propellant in interior ballistics simulations. The use of a nonstandard form of the gas generation rate equation solved this problem. The second problem concerned the assessment of projectile–barrel interaction. The barrel resistance was estimated making use of finite element analysis. The third problem arose from the need to determine the heat transfer from propellant gases to the barrel. The employed formula for the heat exchange coefficient and 2D modelling of the heat conduction in the barrel provided the solution. Selected elements of the theoretical model were validated by shooting range experiments and data provided by the ammunition producer. Using the considered approach, crucial ballistic parameters (maximum propellant gas pressure and muzzle velocity) were estimated with an error of less than 6.0%, without application of additional fitting coefficients. The numerical estimation of the barrel external surface temperature provided a relative discrepancy with the experimental data lower than 6% and enabled the estimation of the critical burst length, equal to 14 shots.

Significant growth in knowledge about metal additive manufacturing (AM) affects the increase of interest in military solutions, where there is always a need for unique technologies and materials. An important section of materials in the military are those dedicated to armour production. An AM material is characterised by different behaviour than those conventionally made, especially during more dynamic loading such as ballistics testing. In this paper, M300 maraging steel behavior was analysed under the condition of ballistic testing. The material was tested before and after solution annealing and ageing. This manuscript also contains some data based on structural analysis and tensile testing with digital image correlation. Based on the conducted research, M300 maraging steel was found to be a helpful material for some armour solutions after pre- or post-processing activities. Conducted solution annealing and ageing increased the ballistic properties by 87% in comparison to build samples. At the same time, the material’s brittleness increased, which affected a significant growth in fragmentation of the perforated plate. According to such phenomena, a detailed fracture analysis was made.