A self-passivating cathode/electrolyte interface achieves stable, room-temperature long-term cycling of 4 V-class Na3(VOPO4)2F|Na4(CB11H12)2(B12H12)|Na all-solid-state sodium batteries with the highest reported discharge cell voltage and cathode-based specific energy.
The research and development of advanced nanocoatings for high-capacity cathode materials is currently a hot topic in the field of solid-state batteries (SSBs). Protective surface coatings prevent direct contact between the cathode material and solid electrolyte, thereby inhibiting detrimental interfacial decomposition reactions. This is particularly important when using lithium thiophosphate superionic solid electrolytes, as these materials exhibit a narrow electrochemical stability window, and therefore, are prone to degradation during battery operation. Herein we show that the cycling performance of LiNbO3-coated Ni-rich LiNixCoyMnzO2 cathode materials is strongly dependent on the sample history and (coating) synthesis conditions. We demonstrate that post-treatment in a pure oxygen atmosphere at 350 ℃ results in the formation of a surface layer with a unique microstructure, consisting of LiNbO3 nanoparticles distributed in a carbonate matrix. If tested at 45 ℃ and C/5 rate in pellet-stack SSB full cells with Li4Ti5O12 and Li6PS5Cl as anode material and solid electrolyte, respectively, around 80% of the initial specific discharge capacity is retained after 200 cycles (~ 160 mAh·g−1, ~ 1.7 mAh·cm−2). Our results highlight the importance of tailoring the coating chemistry to the electrode material(s) for practical SSB applications.
Hydrogen as an energy carrier is very versatile in energy storage applications. Developments in novel, sustainable technologies towards a CO2-free society are needed and the exploration of all-solid-state batteries (ASSBs) as well as solid-state hydrogen storage applications based on metal hydrides can provide solutions for such technologies. However, there are still many technical challenges for both hydrogen storage material and ASSBs related to designing low-cost materials with low-environmental impact. The current materials considered for all-solid-state batteries should have high conductivities for Na+, Mg2+ and Ca2+, while Al3+-based compounds are often marginalised due to the lack of suitable electrode and electrolyte materials. In hydrogen storage materials, the sluggish kinetic behaviour of solid-state hydride materials is one of the key constraints that limit their practical uses. Therefore, it is necessary to overcome the kinetic issues of hydride materials before discussing and considering them on the system level. This review summarizes the achievements of the Marie Skłodowska-Curie Actions (MSCA) innovative training network (ITN) ECOSTORE, the aim of which was the investigation of different aspects of (complex) metal hydride materials. Advances in battery and hydrogen storage materials for the efficient and compact storage of renewable energy production are discussed.
Hydroborate‐based solid electrolytes have recently been successfully employed in high voltage, room temperature all‐solid‐state sodium batteries. The transfer to analogous lithium systems has failed up to now due to the lower conductivity of the corresponding lithium compounds and their high cost. Here LiB11H14nido‐hydroborate as a cost‐effective building block and its high‐purity synthesis is introduced. The crystal structures of anhydrous LiB11H14 as well as of LiB11H14‐based mixed‐anion solid electrolytes are solved and high ionic conductivities of 1.1 × 10−4 S cm−1 for Li2(B11H14)(CB11H12) and 1.1 × 10−3 S cm−1 for Li3(B11H14)(CB9H10)2 are obtained, respectively. LiB11H14 exhibits an oxidative stability limit of 2.6 V versus Li+/Li and the proposed decomposition products are discussed based on density functional theory calculations. Strategies are discussed to improve the stability of these compounds by modifying the chemical structure of the nido‐hydroborate cage. Galvanostatic cycling in symmetric cells with two lithium metal electrodes shows a small overpotential increase from 22.5 to 30 mV after 620 h (up to 0.5 mAh cm−2), demonstrating that the electrolyte is compatible with metallic anodes. Finally, the Li2(B11H14)(CB11H12) electrolyte is employed in a proof‐of‐concept half cell with a TiS2 cathode with a capacity retention of 82% after 150 cycles at C/5.
Rechargeable solid-state magnesium batteries are considered for high energy density storage and usage in mobile applications as well as to store energy from intermittent energy sources, triggering intense research for suitable electrode and electrolyte materials. Recently, magnesium borohydride, Mg(BH4)2, was found to be an effective precursor for solid-state Mg-ion conductors. During the mechanochemical synthesis of these Mg-ion conductors, amorphous Mg(BH4)2 is typically formed and it was postulated that this amorphous phase promotes the conductivity. Here, electrochemical impedance spectroscopy of as-received γ-Mg(BH4)2 and ball milled, amorphous Mg(BH4)2 confirmed that the conductivity of the latter is ~2 orders of magnitude higher than in as-received γ-Mg(BH4)2 at 353 K. Pair distribution function (PDF) analysis of the local structure shows striking similarities up to a length scale of 5.1 Å, suggesting similar conduction pathways in both the crystalline and amorphous sample. Up to 12.27 Å the PDF indicates that a 3D net of interpenetrating channels might still be present in the amorphous phase although less ordered compared to the as-received γ-phase. However, quasi elastic neutron scattering experiments (QENS) were used to study the rotational mobility of the [BH4] units, revealing a much larger fraction of activated [BH4] rotations in amorphous Mg(BH4)2. These findings suggest that the conduction process in amorphous Mg(BH4)2 is supported by stronger rotational mobility, which is proposed to be the so-called “paddle-wheel” mechanism.