Controlling defects and interfaces in composite absorbers can effectively regulate electromagnetic (EM) parameters and enhance the electromagnetic wave (EMW) absorption ability, but the mechanism still needs to be further elucidated. In this study, ZnFe2O4/ZnO/C composite was synthesized via the hydrothermal method followed by post-annealing in different atmospheres. Defects and interfaces were characterized by Raman, PL spectroscopy, XPS and TEM, and their relationship with dielectric loss and EMW absorption performance was discussed in detail. Results show that the N2-annealed ZnFe2O4/ZnO/C composite with abundant defects and interfaces as well as an optimized composition exhibits excellent EMW dissipation ability, with a RLmin value of −17.4 dB and an fe of 3.85 GHz at a thickness of 2.28 mm. The excellent EMW absorption performance originates from suitable impedance matching, significant conduction loss and strong dielectric loss (interfacial polarization, diploe polarization and defect polarization) dominated by lattice defects and interfaces. This study provides a view into the relationship between defects, interfaces, EM parameters and EMW absorption ability, and also suggests an effective way to promote EMW dissipation ability of the absorbers by controlling defects and interfaces.
Magnetic FeGa and FeGaNi films with an in-plane anisotropy were deposited by employing oblique magnetron sputtering. With the increase in oblique angle, the crystallite size of FeGa decreases, which indicates that oblique sputtering can refine the crystallite size. The remanence ratio of FeGa films increases from 0.5 to 0.92 for an easy axis, and the coercivity increases with the decrease in the crystallite size. The calculated static anisotropic field shows that the in-plane magnetic anisotropy can be induced by oblique sputtering and the strength increases with the oblique sputtering angle. After doping Ni by co-sputtering, FeGaNi films exhibit a stable remanence ratio at 0.8, low coercivity and good anisotropy. With the low sputtering power of the Ni target, there is a competitive relationship between the effect of crystallite size and Ni doping which causes the coercivity of FeGaNi films to first increase and then decrease with the increase in the oblique angle. The FeGaNi film also shows high anisotropy in a small oblique angle. The variation of coercivity and anisotropy of FeGaNi films can be explained by the crystalline size effect and increase in Ni content. For the increasing intensity of collisions between FeGa and Ni atoms in the co-sputtering, the in-plane magnetic anisotropy increases first and then decreases. As a result, the magnetic properties of FeGa films were examined to tailor their magnetic softness and magnetic anisotropy by controlling the oblique sputtering angle and Ni doping.
Interfacial polarization is generally a major cause of dielectric loss, but its exact contribution to the electromagnetic wave (EMW) absorption capacity of absorbers remains to be elucidated. In this work, SnO2@rGO composite (S2) with tight interfaces formed by chemical bonds and SnO2/rGO mixture (S3) were synthesized by a simple chemical route followed by further calcined in argon, respectively. Compared with pure SnO2 (S1) and S3, S2 exhibits much better EMW-dissipation ability, with a smaller minimum reflection loss (RLmin) value of −20.5 dB at a matched thickness of 5 mm and a larger effective absorption bandwidth (fe) value of 5.8 GHz (from 11 GHz to 16.8 GHz) at 3.2 mm. By comprehensively comparing the defects, dipoles, and interfaces in S2 and S3, it is concluded that the excellent EMW absorption capacity of S2 is mainly caused by strong dielectric loss dominated by interfacial polarization as well as suitable impedance matching. This study provides an insight into the exact contribution of interfacial polarization to the EMW-dissipation ability of absorbers, showing that the EMW absorption of graphene-based composites can be effectively promoted by constructing well-connected interfaces between graphene and absorbers.
FeGa/FeNi bilayer structures with different deposition order were fabricated by the electrodeposition method on indium tin oxide (ITO) substrates. The structure, morphology, static and dynamic magnetic properties of FeGa/FeNi (FeNi/FeGa) films were investigated. The bilayer structures exhibit extremely various magnetic properties with different deposition order which could be attributed to the different coupling interaction in the interface. When FeGa is on top, the bilayer structures show lower coercivity than when FeNi is on top. Meanwhile, increase of the proportion of FeNi in the bilayer structure could affect the Hc and Mr/Ms. The ferromagnetic resonance peak of FeGa on top moves to a high field compared with FeNi on top. Moreover, FeGa on top shows improved complex permeability and a clear resonant phenomenon of the magnetization. These properties make FeGa/FeNi bilayer structure a potential candidate for high-frequency application.
Metallic magnetic materials are extensively used to mitigate electromagnetic interference due to their high Curie temperatures and permeability. However, their high permittivity often hinders impedance-matching effectiveness, limiting their utility. In this study, amorphous cobalt–iron (Co100−xFex) alloy nanoparticles with relatively low permittivity were synthesized using a simple aqueous reduction method at room temperature. The effect of atomic ratio variation on the microwave absorption properties of these nanoparticles was investigated across 2–18 GHz. The amorphous Co100−xFex nanoparticles exhibited excellent electromagnetic wave absorption performance, achieving an effective absorption bandwidth of 5.6 GHz, a matching thickness of 2.60 mm, and a reflection loss of −42 dB.