The process of biomass compaction depends on many factors, related to material and process. One of the most important is the proper fragmentation of the raw material. In most cases, more fragmented raw material makes it easier to achieve the desired quality parameters of pellets or briquettes. While the chipping of biomass prefers moist materials, for grinding, the material needs to be dried. As drying temperature changes the properties of the material, these may affect the grinding process. The aim of this work was to determine the influence of the drying temperature of biomass raw material in the range of 60–140 °C on the biomass grindability. To only determine this effect, without the influence of moisture, grinding was carried out on the material in a dry state. The research was carried out on a mill with a knife and hammer grinding system, which is the most popular in the fragmentation of biomass. The analysis of particle size distribution and bulk density of the obtained material was carried out. The energy demand for the grinding process was determined and it was shown that drying temperature, grinding system, and mainly type of biomass affects the grindability.

Increasing production of waste has compelled the development of modern technologies for waste management. Certain fractions of municipal solid wastes are not suitable for recycling and must be utilised in other ways. Materials such as refuse-derived fuel (RDF) fractions are used as fuel in cement or CHP (combined heat and power) plants. The low bulk density leads to many problems pertaining to transportation and storage. In the case of biomass, these problems cause reduction in pelletisation. This paper therefore presents a comprehensive study on RDF pellet production, which is divided into three major areas. The first describes laboratory-scale tests and provides information on key factors that affect pellet quality (e.g., density and durability). Based on this, the second part presents a design of modified RDF dies to form RDF pellets, which are then tested via a semi-professional line test. The results show that RDF fraction can be compacted to form pellets using conventional devices. Given that temperature plays a key role, a special die must be used, and this ensures that the produced pellets exhibit high durability and bulk density, similar to biomass pellets.

The paper presents the results of research aimed at evaluating the possibility of using selected tree leaf species to produce solid biofuels. The possibility of production of qualitative solid biofuels from urban tree leaves meets the expectations of the municipal sector. Collection of tree leaves in urban areas is very often necessary for road safety reasons, the need to collect biomass rich in dust and pollution as well as biomass infested with pests. The production of solid biofuels from tree leaves allows for effective management of this raw material with energy recovery. The performed research indicates such a possibility, and the obtained ash is used as a soil improver. The conducted research showed that the biomass of leaves of five tree species used in the experiment can be a source of raw materials for production of qualitative biofuels. The obtained pellets were characterized by properties comparable to those of classical wood pellets. The lower heating value of the obtained pellets ranged from 14.5 to 15.5 MJ∙kg⁻¹. Physical properties of the obtained pellets described by bulk density (BD 600–660 kg∙m⁻³), mechanical durability (DU 90–96%), moisture (M_ar 10–12.5%) indicate that these products can be used in existing combustion equipment. Preliminary analysis of the obtained ashes (determination of ash melting point, bulk density) indicates that they should not cause difficulties in ash removal systems from the combustion chamber.

The article analyzed the state of the global problem of ecological safety of the EU and argued the need to create a methodology for planning technologically integrated projects of the “European Green Deal” (TIP “EGD”) that accounts for the risks to the stakeholders, i.e., the state, project executors, resource suppliers, project managers, and clients. Each of these has an individual set of values that determines the project risk for them. Herein is proposed a taxonomy of three ranks of TIP “EGD” involving agricultural waste, determined by their characteristics, products, and requirements for the stakeholders. The authors point out the need to create tools for quantitative risk assessment for the stakeholders of TIP “EGD” involving agricultural waste and distinguish four groups of risk components with regard to the value of such projects. A model of value risk formation is presented that addresses the risk management of each of these stakeholder values. The need to develop tools (models, methods, and algorithms) for quantitative risk assessment of the values of each type of project is discussed. Regularities in the formation of stakeholder values, which were a foundation of the model of formation, are established.

For biomass compaction, it is important to determine all aspects of the process that will affect the quality of pellets and briquettes. The low bulk density of biomass leads to many problems in transportation and storage, necessitating the use of a compaction process to ensure a solid density of at least 1000 kg·m⁻³ and bulk density of at least 600 kg·m⁻³. These parameters should be achieved at a relatively low compaction pressure that can be achieved through the proper preparation of the raw material. As the compaction process includes a drying stage, the aim of this work is to determine the influence of the drying temperature of pine biomass in the range of 60–140 °C on the compaction process. To determine whether this effect is compensated by the moisture, compaction was carried out on the material in a dry state and on the materials with moisture contents of 5% and 10% and for compacting pressures in the 130.8–457.8 MPa range. It was shown that drying temperature affects the specific density and mechanical durability of the pellets obtained from the raw material in the dry state, while an increase in the moisture content of the raw material neutralizes this effect.