The discovery of ferroelectricity in HfO2-based materials in 2011 provided new research directions and opportunities. In particular, for atomic layer deposited Hf0.5Zr0.5O2 (HZO) films, it is possible to obtain homogenous thin films with satisfactory ferroelectric properties at a low thermal budget process. Based on experiment demonstrations over the past 10 years, it is well known that HZO films show excellent ferroelectricity when sandwiched between TiN top and bottom electrodes. This work reports a comprehensive study on the effect of TiN top and bottom electrodes on the ferroelectric properties of HZO thin films (10 nm). Investigations showed that during HZO crystallization, the TiN bottom electrode promoted ferroelectric phase formation (by oxygen scavenging) and the TiN top electrode inhibited non-ferroelectric phase formation (by stress-induced crystallization). In addition, it was confirmed that the TiN top and bottom electrodes acted as a barrier layer to hydrogen diffusion into the HZO thin film during annealing in a hydrogen-containing atmosphere. These features make the TiN electrodes a useful strategy for improving and preserving the ferroelectric properties of HZO thin films for next-generation memory applications.
In this Letter, the robust ferroelectric properties of low-temperature (350 °C) Hf0.5Zr0.5O2 (HZO) films are investigated. We demonstrate that the lower crystallization temperature of HZO films originates from a densified film deposition with an anhydrous H2O2 oxidant in the atomic layer deposition process. As a consequence of this densification, H2O2-based HZO films showed completely crystallinity with fewer defects at a lower annealing temperature of 350 °C. This reduction in the crystallization temperature additionally suppresses the oxidation of TiN electrodes, thereby improving device reliability. The low-temperature crystallization process produces an H2O2-based HZO capacitor with a high remanent polarization (Pr), reduced leakage current, high breakdown voltage, and better endurance. Furthermore, while an O3-based HZO capacitor requires wake-up cycling to achieve stable Pr, the H2O2-based HZO capacitor demonstrates a significantly reduced wake-up nature. Anhydrous H2O2 oxidant enables the fabrication of a more reliable ferroelectric HZO device using a low process thermal budget (350 °C).
19 August 2020 in Journal of Materials Chemistry C
Trisilylamine (TSA), an exemplary chlorine and carbon-free commercial silylamine precursor, is well-known to induce improvements in the process and properties of silicon nitride (SiNx) thin films grown using atomic layer deposition (ALD). Herein, we report a TSA homolog, tris(disilanyl)amine (TDSA), as a novel chlorine and carbon-free precursor for the deposition of highly etch resistant SiNx thin films having a high growth rate at a low temperature (<300 °C) using plasma enhanced ALD (PEALD) with hollow cathode plasma (HCP). These improvements in PEALD SiNx using TDSA may be attributed to higher surface reactivity of the molecule enabled by weaker Si–N bonds, higher molecular polarity and the existence of reactive Si–Si bonds in the molecule. The performance of PEALD SiNx grown by TDSA has been compared with that of TSA, aminosilanes and chlorosilanes, and explained with the structure–property relationship of the molecule. TDSA grows SiNx film faster than TSA. Furthermore, the TDSA precursor produces SiNx films that have lower wet etch rate (WER) when compared to other silylamine precursors like TSA, or other types of silane precursors such as aminosilanes and chlorosilanes. We believe that the result, that TDSA-grown SiNx films exhibit lower WER than TSA-grown SiNx films, can be attributed to the abundance of Si in SiNx films, which thereby offers high resistance to a wet etch.
11 February 2022 in Journal of Vacuum Science & Technology A
A novel precursor, 1,1,1-tris(dimethylamino)disilane {TADS, [(H3C)2N]3Si2H3}, is used to deposit silicon dioxide (SiO2) films in a temperature range of 115–480 °C by thermal atomic layer deposition (tALD) and plasma-enhanced atomic layer deposition (PEALD) techniques. Compared to tris(dimethylamino)silane (TDMAS), the additional Si-Si bond in TADS is expected to enhance the reactivity of the molecule due to the polarization of the bond. In the tALD process, TADS gives a growth rate of 0.06 nm/cycle, which is approximately 20% higher than that of TDMAS, and an excellent conformality (>95% step coverage) in high aspect ratio nanotrenches (6:1). In the case of the PEALD process, TADS leads to not only a higher or at least comparable growth rates (0.11 nm/cycle), but also a higher bulk film density (∼2.38 g/cm3). As a result, the PEALD SiO2 films of TADS show a wet-etch rate down to 1.6 nm/min in 200:1 HF, which is comparable to that of the thermal oxide. Analyzed with Fourier-Transform Infrared (FTIR), the SiO2 films contain predominant Si−O bonds and a low level of Si−H and O−H bonds, consistent with the observed high wet-etch resistance. Furthermore, the PEALD SiO2 films deposited at 310 °C have at least 75% step coverage in high aspect ratio nanotrenches, suggesting that TADS is applicable for forming high-quality SiO2 films on both planar and patterned surfaces.
In this letter, a threshold switching (TS) selector with Ag doping-based nano-polycrystalline ZnO switching layer (SL) having (002) preferred orientation has been manifested, without incorporating an active Ag metal layer, using a facile co-sputtering deposition technique. The TS selectors with extremely controlled doping of ~0.14 at. % Ag concentration showed remarkable electroforming (EF)-free selection behavior such as gigantic selectivity (~10 11 ), extreme-low off -current (~10 fA), high on -current density (~1.6 MA/cm 2 ), ultra-steep switching slope (~0.8 mV/decade), satisfactory endurance (>10 6 ), fast switch- on speed (~38 ns) and relaxation speed (~64 ns), and high device yield (~90%). Furthermore, selector devices showed reproducible selection behavior with stable threshold voltage (V th ) having merely ~8% variances.
In this work, a nano-polycrystalline Ag-doped ZnO-based threshold switching (TS) selector via a facile co-sputtering technique is investigated without using an Ag active metal layer. The effects of the Ag concentration with respect to OFF-state leakage current (Ioff) were studied, and the results demonstrate that by regulating the Ag doping concentration in the switching layer (SL), an electroforming-free switching with an Ion/Ioff ratio of ∼108 could be achieved, having an extremely low Ioff value of ∼10−13 A. Furthermore, cycling endurance can also be improved as the formation of a laterally thick and stable filament does not happen promptly with consequent measurements when there is a limited amount of Ag in the SL. The selector device performance enhancement is attributed to the doping-based polycrystalline structure that facilitates enhanced control on filament formation due to the restricted availability and anisotropic diffusion of Ag ions in the polycrystalline ZnO SL, thereby trimming down the overall stochasticity during metallic filament growth. The present study demonstrates that a doping-based polycrystalline SL structure can be implemented in a selector device to augment TS characteristics, i.e., device variances and cycling endurance for adoption in ultra-high density memory applications.