Alexandru Viorel Vasiliu

Dr. Alexandru Viorel Vasiliu

SDIMI, "Dunarea de Jos" University of Galati, Galaţi, Romania
orcid
Improving the optimizer!

Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
5 July 2024 in Polymers
Verified
Journal Article
Open access
PDF file
ICIoana Gabriela Chiracu
Ioana Gabriela Chiracu
Ojoc George-GhiocelOjoc George-Ghiocel
Ojoc George-Ghiocel
GCGeorge Catalin Cristea
George Catalin Cristea
Mihail BOTANMihail BOTAN
Mihail BOTAN
ACAlina Mihaela Cantaragiu Ceoromila
Alina Mihaela Cantaragiu Ceoromila
Lorena DeleanuLorena Deleanu
Lorena Deleanu
This paper presents experimental results from three-point bending tests for a composite made of quadriaxial glass fiber fabrics and an epoxy resin. Two composites were tested, one with 8 layers and the other with 16 layers; both had the same matrix (the epoxy resin). Tests were carried out, using five different test rates from 10 mm/min to 1000 mm/min. The following parameters were recorded and calculated: Young’s modulus, flexural stress, flexural strain, energy, force, and all four for the first peak. The experimental data reveal no sensitivity for these materials based on the test rates, at least for the analyzed range; but, the characteristics for the thicker composite, with 16 layers of fabric, are slightly lower than those for the thinner composite, with 8 layers. The results pointed out that, for the same thickness of composite, certain characteristics, such as stress at the first peak, the flexural modulus, strain at the first peak, and energy at the first peak, are not sensitive to the test rate in the range 10–1000 mm/min. The energy at the first peak is double for the 16-layer composite compared to the 8-layer composite, but the specific energy (as energy on cross-sectional area) has close values: 103.47 kJ/m2 for the 8-layer composite and 106.51 kJ/m2 for the 16-layer composite. The results recommend this composite for applications in components with resistance to bending or for low-velocity impact protection.

14 April 2025 in Polymers
Verified
Journal Article
Open access
PDF file
ACAlina Mihaela Cantaragiu Ceoromila
Alina Mihaela Cantaragiu Ceoromila
Lorena DeleanuLorena Deleanu
Lorena Deleanu
CPChristian Popescu
Christian Popescu
ILIonut Lom
Ionut Lom
Alexandru Viorel VasiliuAlexandru Viorel Vasiliu
Alexandru Viorel Vasiliu
SSSimona Maria Sandu
Simona Maria Sandu
This paper presents a synthesis of failures of aramid fibers used in protective systems, with the help of SEM images obtained from three types of samples (panels made of fabrics with aramid fibers) tested against bullets, knives and spikes. This investigation is useful when using a step-by-step magnification and even macro photos in order to explain the mechanical failures of fibers. Several types of failure mechanisms (shear and tensile break, local bending, debonding from the matrix, fibrillation, local necking, etc.) were detected and discussed. Almost all of these failure mechanisms are present, with different densities of occurrence, in the studied panels made of aramid fibers. The description of failure mechanisms had to be conducted following the test conditions accurately. Failure mechanisms of aramid fibers are particularly relevant due to their specific molecular chains making them adequate for applications like ballistic and bladed weapon attacks.

28 January 2025 in Polymers
Verified
Journal Article
Open access
PDF file
GCGeorge Catalin Cristea
George Catalin Cristea
Lorena DeleanuLorena Deleanu
Lorena Deleanu
ICIoana Gabriela Chiracu
Ioana Gabriela Chiracu
Mihail BOTANMihail BOTAN
Mihail BOTAN
Ojoc George-GhiocelOjoc George-Ghiocel
Ojoc George-Ghiocel
ACAlina Mihaela Cantaragiu Ceoromila
Alina Mihaela Cantaragiu Ceoromila
In this study, the composition and mechanical properties of composites designed for shipbuilding are described. Four different composites were designed and fabricated by the research team, using quadriaxial glass fiber fabric (eight layers in all composites), two different resins (the epoxy resin SikaBiresin® CR82 with the hardener CH80-2 or the polyester resin Enydyne H 68372 TA with Metox-50 W as the accelerator), and a middle layer of Coremat Xi 3 (only applied in some composites). The experimental results of low-velocity impact tests are also discussed, including the graphics force (displacement) and absorbed energy (displacement and velocity). The displacement and composite quality were evaluated through several parameters, such as maximum force, absorbed energy, and maximum displacement. Impact tests were carried out using four impact energy values (50–200 J), with an average impact velocity in the range of 4.37 ± 0.05 m/s. Only partial penetrations were obtained for all tested composites. For the low energy tests (50 J), the four composite materials were not well differentiated by graph shapes and parameter values, but for the higher energy tests, the composites containing Coremat Xi 3 displayed better behavior, having Fmax reduced with 10.8% to 29.08%. The higher absorbed energy of these composites can be explained by the plateau generated by the force from a longer impactor displacement in contact with the composite. The results generated in this study confirm the suitability of the designed composites for shipbuilding applications. Still, the composites have light differences in terms of energy absorption in low-velocity impact and a significant reduction in maximum force.

23 March 2024 in Polymers
Verified
Journal Article
Open access
PDF file
Lorena DeleanuLorena Deleanu
Lorena Deleanu
VRViorel Totolici Rusu
Viorel Totolici Rusu
Ojoc George-GhiocelOjoc George-Ghiocel
Ojoc George-Ghiocel
GCGeorge Catalin Cristea
George Catalin Cristea
Mihail BOTANMihail BOTAN
Mihail BOTAN
CPChristian Popescu
Christian Popescu
This paper presents research on several factors influencing the stabbing behaviour of stratified panels made of aramid fabric Twaron® SRM509 Teijin Aramid BV (Arnhem, The Netherlands). The inputs in the test campaign were the number of layers, the impact energy, and the sample size. Tests were performed on small samples (130 mm × 130 mm) on an Instron® CEAST 9350 drop-tower impact system (Norwood, MA, USA) and on larger samples (400 mm × 400 mm) using a test installation with the same values of the impact energy. Knife type S1 was used, with the geometry recommended in NIJ Standard 0115.00 Stab Resistance of Body Armor SEM, and macro photography investigations revealed the failure mechanisms of panel, layers and fibres. A very important conclusion of this study regarding the stabbing performance of fabric Twaron® SRM 509 in particular, but also in general for panels for body protection is that a research study could start on small size samples, with an accurately instrumented machine, in order to establish the influence of significant factors of stab resistance (energy level, number of layers in a panel, etc.), as these samples are less expensive and less time consuming, but the study should be continued to examine larger size samples. The obtained data are useful for the prototype.

27 November 2024 in Aerospace
Verified
Journal Article
Open access
PDF file
DIDaniel IORGA
Daniel IORGA
CGConstantin Georgescu
Constantin Georgescu
SCSorin Constantinescu
Sorin Constantinescu
Ojoc George-GhiocelOjoc George-Ghiocel
Ojoc George-Ghiocel
Alexandru Viorel VasiliuAlexandru Viorel Vasiliu
Alexandru Viorel Vasiliu
Lorena DeleanuLorena Deleanu
Lorena Deleanu
Considering the advantages of using expanded polystyrene (EPS) reinforced with adhesive tape made of glass fibers, this paper presents a design and technological solution for a functional drone of class C1, meaning a maximum take-off mass of 900 g, and tests validating the use of EPS for small UAVs under flight conditions. The selected profile was MH-49, which had a maximum chord thickness of 10.5%. This profile demonstrated a much lower coefficient of pitching moment than that of the NACA 63215 profile, giving this flying-wing UAV superior governability. This airfoil implies a geometry with greater attenuation of the trailing edge, and the design favors the placement of stress concentrators towards the trailing edge. Due to the use of fiberglass tape reinforcement technology, it is possible to address this profile, implying improved aerodynamic performance. The use of EPS in the disposable UAV industry may bring significant benefits, contributing to the development of high-performance, versatile, and low-cost UAVs, suitable for a wide range of tactical and logistic applications. This study presents the design, the fabrication, and testing of this drone, highlighting the advantages and possible challenges of the proposed solution.

10 March 2025 in Journal of Engineering Sciences and Innovation
Verified
Journal Article
Closed access
Lorena DeleanuLorena Deleanu
Lorena Deleanu
CPCristina Popa
Cristina Popa
Ojoc George-GhiocelOjoc George-Ghiocel
Ojoc George-Ghiocel
1T1 Aeroportului Autonomous Flight Technologies
1 Aeroportului Autonomous Flight Technologies
GCGeorge Cătălin Cristea
George Cătălin Cristea
ACAlina Mihaela Cantaragiu Ceoromila
Alina Mihaela Cantaragiu Ceoromila
This paper discusses the terminology used at nano level concerning materials, technology and characterization, to promote adequate vocabulary and definitions, as recognized in international standards and reference works. The ISO Technical Committee for Nano Sciences 229 has pointed out current ISO standards related to terminology in this active field of research and applications. Research and applications involving the nano level, often referred to as nanoscience or nanotechnology, involves the study and manipulation of materials at the atomic, molecular and macromolecular scale, typically between 1 and 100 nanometers. There are discussed aspects characterizing this emerging domain: size and scale, material properties, interdisciplinarity of research and nano technologies, techniques and equipment for investigations, fabrication methods, new processes and applications, challenges, regulation and standardization. Because elf the authors’ specialization, the discussions are related especially to mechanical engineering and less for chemical aspects at nano level.