This study examines a catalyst based on graphitic carbon nitride (g-C3N4) for synthesizing glycerol carbonate through the coupling reaction of glycerol and CO2. In this research, we focus on simultaneously improving CO2 emission reduction and glycerol valorization by co-doping g-C3N4 with phosphorus (P), sulfur (S), magnesium (Mg), and lithium (Li) for a better catalytic performance. The catalysts were prepared through a one-step thermal condensation process and characterized using XRD, SEM, TGA, FTIR, and nitrogen adsorption–desorption techniques. The co-doping further enhanced the surface chemical properties, Lewis acidity, basicity, and thermal stability, evidenced by the lower crystallinity, wider pore, and better catalytic performance as assessed through glycerol carbonylation reaction, optimized using a Box–Behnken design. The MgPSCN catalyst exhibited the highest glycerol conversion (68.72%) and glycerol carbonate yield (44.90%) at 250 °C, using 50 mg catalyst and 10 bar pressure. The model accuracy was validated by ANOVA (R2 > 0.99; p values < 0.0001). The results indicated that doping significantly enhanced the catalytic performance, most likely due to improved electron charge transfer and structural distortions within the g-C3N4 framework. Such a process highlights the potential of co-doped g-C3N4 catalysts for the sustainable glycerol utilization and valorization of CO2 through a scalable pathway toward green chemical synthesis—an approach that comes in line with worldwide decarbonization goals.
Biochar activation is achieved by removing tar formed in the pores during the thermal treatment of biomass, thereby increasing pore volume. This process typically involves entraining tar with steam at elevated temperatures for extended durations. In this study, a reduction in lignin content in grape seeds through partial solubilization, prior to thermal treatment, is proposed. Initially, grape seeds were treated with a basic sodium sulfide solution, followed by conditioning with either phosphoric acid or zinc chloride and then drying and calcination. The synthesized adsorbents were characterized using scanning electron microscopy (SEM), textural analysis, Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), and evaluation of toluene adsorption capacity. Textural analysis indicated that conditioning with phosphoric acid or zinc chloride increased the specific surface area of biochar by over 20%, with a higher increase observed for phosphoric acid treatment. The toluene adsorption capacity of the adsorbents was assessed in a continuous fixed-bed system. Biochar pretreated with ZnCl2 exhibited an adsorption capacity of 0.11 cm3 of toluene per gram, while biochar pretreated with phosphoric acid demonstrated a capacity of 0.14 cm3 per gram. These results indicate that preliminary delignification of grape seed biomass maintains its adsorption capacity of toluene at levels comparable to other adsorbents, despite a lower activation temperature.
Adding nanomaterials to polymer membranes can improve certain properties, such as the photocatalytic degradation of contaminants and antibacterial qualities. However, the interaction between nanomaterials and polymers is often limited by the presence of functional groups that can trap nanostructures within the polymer matrix. This study focuses on the synthesis of silver-decorated graphene oxide nanoparticles and their integration into cellulose acetate membranes. Characterization of the membranes was conducted using various techniques, including electron microscopy (SEM), thermogravimetric analysis, FTIR, goniometry, and filterability tests. The results indicate that CA membranes with decorated nanoparticles exhibit improved thermal stability, making them more effective for removing heavy hydrocarbons without the risk of nanomaterial elution during temperature fluctuations in the contaminated water flow subjected to filtration. Furthermore, these decorated structures enhance hydrophobicity due to interactions between the oxygenated groups of GrO and silver ions. While these additional networks may reduce the permeate flow rate, they significantly increase the efficiency of contaminant removal.
In this study, a novel magnetic nanocatalyst based on tin ferrite (SnFe2O4) was synthesized via a chemical co-precipitation method and thoroughly characterized using XRD, SEM, TGA-DTG, BET, FTIR, and FTIR-pyridine techniques. The catalyst exhibited high crystallinity, a mesoporous structure with a specific surface area of 79.7 m2/g, and well-defined Lewis and Brønsted acid sites. Its catalytic performance was assessed in the esterification of glycerol with acetic acid to produce monoacetin (MAG), diacetin (DAG), and triacetin (TAG). A Box–Behnken experimental design was employed to evaluate the influence of temperature, catalyst loading, and the acetic-acid-to-glycerol molar ratio on product distribution and glycerol conversion. Statistical analysis and regression modeling revealed excellent predictive accuracy (R2 > 0.99), confirming the robustness of the model. Optimal reaction conditions (110 °C, 2 wt.% catalyst, and AA/GLY ratio of 3.6) yielded a maximum glycerol conversion of 93.2% and a combined DAG and TAG yield of ~59.1%. These results demonstrate the high efficiency and selectivity of the synthesized SnFe2O4 catalyst, making it a promising candidate for sustainable glycerol valorization.
The experiments in this study investigated the toxicity of naphthenic acids (NAs) on the algal culture Spirulina platensis. The tests monitored the progression of the algal suspension in media contaminated with various concentrations of naphthenic acids. The evolution of the algal culture during the metabolism of NAs was investigated. The monitoring also included the determination of the values of some parameters during the biodegradation process (pH, conductivity, cell viability, dissolved oxygen). Optical density measurements (OD600) were used to quantify the growth of Spirulina platensis, alongside the determination of the sedimentation index (IS). Cell viability was assessed microscopically using TEM and optical microscopy. The results facilitated the estimation of the percentage of cell growth inhibition and the inhibitory concentration value, determined by estimating ECb50 (concentration of NAs corresponding to 50% inhibition). The chemical quantification of naphthenic acids in the samples analyzed was performed by calculating the acidity value (AV) and characterizing the naphthenic acids through FTIR analysis. The graphical representation of ECb50 was established by extrapolating to a concentration of 110 mg/mL of naphthenic acids. We have demonstrated that pollution caused by NAs can be mitigated by the algae Spirulina platensis, which can metabolize these compounds and thus biodegrade them.
This study investigates the synthesis of biodiesel from three vegetable oils with significantly different chemical compositions. Based on the properties of these biodiesel samples, a method was proposed to estimate the density of petrodiesel–biodiesel blends using an artificial neural network (ANN). The ANN employed in this research consisted of 10 neurons. The experimental data showed a high correlation, indicating effective training and precise estimations in relation to the provided training data. The accuracy of the estimations was evaluated by comparing the blending densities determined through the method presented in this study with the mean of three estimations generated by the neural network. The deviation between the determined and estimated values ranged from 4.1 to 25.2 kg/m3, which is attributable to the limited size of the training database. Most errors fell between −7.1% and 3.8%, with the lowest error being observed for petrodiesel–Brassica carinata biodiesel blends. Excellent correlations for both training and validation data were obtained (R = 0.99 and R = 0.98) for blends incorporating palm and Brassica carinata biodiesel. The estimation method using neural networks proposed in this paper can be effectively adapted for other mixtures and to estimate additional blending properties, accommodating each user’s needs.