This study reports the optical, structural, electrical and dielectric properties of Poly (vinyl alcohol) thin films membranes with embedded ZnO nanoparticles (PVA/ZnO) obtained by the solution casting method at low temperature of deposition. Fourier Transform Infrared spectra showed the characteristics peaks, which correspond to O–H and Zn–O bonds present in the hybrid material. The X-ray diffraction patterns indicated the presence of ZnO structure into the films. The composite material showed low absorbance and a wide band of gap energy from 5.5 to 5.83 eV. The surface morphology for the thin films of PVA/ZnO was studied by Atomic Force Microscopy and Scanning Electron Microscopy. The electrical properties of the membranes were also characterized by current-voltage characteristics and the DC conductivity showed Arrhenius behavior with values of activation energy from 0.62 to 0.78 eV and maximum conductivity at 2.4 × 10−12 S/cm. The dielectric properties of the nanocomposites were measured from low to high frequencies, and the results showed a high dielectric constant (ε) in the order of 104 at low frequency and values from ε ≈ 2000 to 100 in the range of 1 KHz–1 MHz respectively. The properties of PVA/ZnO such as the high permittivity and the low temperature of processing make it a suitable material for potential applications in the development of flexible electronic devices.
In this paper, a n-i-p planar heterojunction simulation of Sn-based iodide perovskite solar cell (PSC) is proposed. The solar cell structure consists of a Fluorine-doped tin oxide (FTO) substrate on which titanium oxide (TiO2) is placed; this material will act as an electron transporting layer (ETL); then, we have the tin perovskite CH3NH3SnI3 (MASnI3) which is the absorber layer and next a copper zinc and tin sulfide (CZTS) that will have the function of a hole transporting layer (HTL). This material is used due to its simple synthesis process and band tuning, in addition to presenting good electrical properties and stability; it is also a low-cost and non-toxic inorganic material. Finally, gold (Au) is placed as a back contact. The lead-free perovskite solar cell was simulated using a Solar Cell Capacitance Simulator (SCAPS-1D). The simulations were performed under AM 1.5G light illumination and focused on getting the best efficiency of the solar cell proposed. The thickness of MASnI3 and CZTS, band gap of CZTS, operating temperature in the range between 250 K and 350 K, acceptor concentration and defect density of absorber layer were the parameters optimized in the solar cell device. The simulation results indicate that absorber thicknesses of 500 nm and 300 nm for CZTS are appropriate for the solar cell. Further, when optimum values of the acceptor density (NA) and defect density (Nt), 1016 cm−3 and 1014 cm−3, respectively, were used, the best electrical values were obtained: Jsc of 31.66 mA/cm2, Voc of 0.96 V, FF of 67% and PCE of 20.28%. Due to the enhanced performance parameters, the structure of the device could be used in applications for a solar energy harvesting system.
The assessment of photovoltaic devices, which convert light energy into electricity, has become significantly more relevant due to the aspiration to reduce pollution on a global scale. In this context, the pursuit of optimizing the efficiency of converting light energy into electrical energy involves exhaustive studies and structural analyses of solar cells, all directed toward achieving this goal. This study introduces a research proposal aimed at analyzing the losses associated with series resistance (Rs). The analysis takes into account each component comprising this resistance, proposing a network of resistances that precisely models each of these elements. The aforementioned research focused on simple-structured crystalline silicon cells. During this investigation, the junction depth (xj) of the n-p materials was varied, with the aim of achieving efficiencies in the range of 12%. However, in the pursuit of this desired efficiency, a significant impact on series resistance was observed when analyzing the I-V curves of the cells obtained in each manufacturing process.
Mixed-halide perovskites enable the creation of high-performance and low-cost solar cells. Chloride incorporation enhances film morphology, carrier diffusion length, and stability, improving device performance. Nevertheless, optimizing film thickness, defect density, and metal contact work function remains insufficiently explored, despite its potential to enhance power conversion efficiency. In this study, a numerical simulation was performed using SCAPS-1D (version 3.3.10) to identify the optimal parameters for the FTO/TiO2/CH3NH3Pb3−xClx/Spiro-OMeTAD/Au configuration. The best performance parameters that have been published in the literature based on experimental results are as follows: VOC = 1.077 V, JSC = 21.45 mA/cm2, FF = 77.57%, and PCE = 17.97%. In contrast, the performance parameters obtained from numerical simulations for the same structure are VOC = 1.28 V, JSC = 21.63 mA/cm2, FF = 78%, and PCE = 21.53%. In our numerical analysis, we achieved efficiencies that were comparable to those reported in experimental studies, and after optimization, superior performance parameters were attained, including VOC = 1.179 V, JSC = 27.26 mA/cm2, FF = 81.03%, and PCE = 26.07%. These results indicate that optimized parameters can be integrated into the design and fabrication of mixed-halide perovskite solar cells to enhance performance.
Inverted perovskite solar cells (PSCs) have gained much attention due to their low hysteresis effect, easy fabrication, and good stability. In this research, an inverted perovskite solar cell ITO/PEDOT:PSS/CH3NH3PbI3/PCBM/Ag structure was simulated and optimized using SCAPS-1D version 3.3.10 software. The influence on the device of parameters, including perovskite thickness, total defect density, series and shunt resistances, and operating temperature, are discussed and analyzed. With optimized parameters, the efficiency increased from 13.47% to 18.33%. Then, a new /ITO/PEDOT:PSS/CH3NH3PbI3/PCBM/Ag device was proposed which includes a silicon-rich oxide () layer. This material was used as the down-conversion energy material, which converts high-energy photons (ultraviolet UV light) into low-energy photons (visible light), improving the stability and absorption of the device. Finally, with , we obtained an efficiency of 22.46% in the simulation. Therefore, the device with the layer is the most suitable as it has better values for current density–voltage output and quantum efficiency than the device without .