Hassan Abd-Elhafez

Dr. Hassan Abd-Elhafez

Associate Professor, College of Engineering-Unaizah, Qassim University
+1
orcid

Research Focus & Metrics

Academic Career Length

17Years (2010-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
21 February 2021 in Metals
Verified
Journal Article
Open access
PDF file
AAAbdulrahman Alateyah
Abdulrahman Alateyah
TAT.A. Aljohani
T.A. Aljohani
MAMajed O. Alawad
Majed O. Alawad
Hassan Abd-ElhafezHassan Abd-Elhafez
Hassan Abd-Elhafez
AAAbdulrahman Almutairi
Abdulrahman Almutairi
Waleed El-GaraihyWaleed El-Garaihy
Waleed El-Garaihy
This study aims to establish the effects of equal channel angular pressing (ECAP) processing on the corrosion behavior and hardness values of the AZ31 Mg alloy. The AZ31 billets were processed through ECAP successfully at 250 °C and their microstructural evolution was studied using optical and field emission scanning electron microscopy. The corrosion resistance of the AZ31 alloy was studied before and after processing through ECAP. The homogeneity of the hardness distribution was studied using both sections cut parallel and perpendicular to the extrusion direction. ECAP processing resulted in highly deformed central regions with elongated grains aligned parallel to the extrusion direction, whereas the peripheral regions showed an ultra-fine-grain recrystallized structure. After processing, small ultra-fine secondary particles were found to be homogeneously dispersed alongside the grain boundaries of the α-Mg matrix. Regarding the corrosion properties, measurements showed that ECAP processing through 1-P and 2-Bc resulted in decreasing their corrosion rate to 67.7% and 78.3%, respectively, of their as-annealed counterpart’s. The corrosion resistance of the ECAPed Mg alloy increased with the number of processing passes. This was due to the refinement of the grain size of the α-Mg matrix and secondary phases till ultra-fine size, caused by the accumulation of strain during processing. On the other hand, ECAP processing through 2-Bc resulted in increasing the Vickers hardness values by 132% and 71.8% at the peripheral and central areas, respectively, compared to the as-annealed counterpart.

9 April 2021 in Metals
Verified
Journal Article
Open access
PDF file
AAAbdulrahman Alateyah
Abdulrahman Alateyah
Mohamed Mohamed Zaky AhmedMohamed Mohamed Zaky Ahmed
Mohamed Mohamed Zaky Ahmed
ZYZedan Yasser
Zedan Yasser
Hassan Abd-ElhafezHassan Abd-Elhafez
Hassan Abd-Elhafez
MAMajed O. Alawad
Majed O. Alawad
Waleed El-GaraihyWaleed El-Garaihy
Waleed El-Garaihy
The current study presents a detailed investigation for the equal channel angular pressing of pure copper through two regimes. The first was equal channel angular pressing (ECAP) processing at room temperature and the second was ECAP processing at 200 °C for up to 4-passes of route Bc. The grain structure and texture was investigated using electron back scattering diffraction (EBSD) across the whole sample cross-section and also the hardness and the tensile properties. The microstructure obtained after 1-pass at room temperature revealed finer equiaxed grains of about 3.89 µm down to submicrons with a high density of twin compared to the starting material. Additionally, a notable increase in the low angle grain boundaries (LAGBs) density was observed. This microstructure was found to be homogenous through the sample cross section. Further straining up to 2-passes showed a significant reduction of the average grain size to 2.97 µm with observable heterogeneous distribution of grains size. On the other hand, increasing the strain up to 4-passes enhanced the homogeneity of grain size distribution. The texture after 4-passes resembled the simple shear texture with about 7 times random. Conducting the ECAP processing at 200 °C resulted in a severely deformed microstructure with the highest fraction of submicron grains and high density of substructures was also observed. ECAP processing through 4-passes at room temperature experienced a significant increase in both hardness and tensile strength up to 180% and 124%, respectively.

24 July 2010 in Journal of Materials Engineering and Performance
Verified
Journal Article
Closed access
PDF file
Hassan Abd-ElhafezHassan Abd-Elhafez
Hassan Abd-Elhafez

25 July 2020 in SAE International Journal of Materials and Manufacturing
Verified
Journal Article
Closed access
AAAbdulrahman Alateyah
Abdulrahman Alateyah
Mohammed AlbadraniMohammed Albadrani
Mohammed Albadrani
Hassan Abd-ElhafezHassan Abd-Elhafez
Hassan Abd-Elhafez
Waleed El-GaraihyWaleed El-Garaihy
Waleed El-Garaihy

6 July 2021 in Manufacturing Review
Verified
Journal Article
Open access
PDF file
EEEman ElShrief
Eman ElShrief
AEAbla El-Megharbel
Abla El-Megharbel
ADAly El Domiaty
Aly El Domiaty
Hassan Abd-ElhafezHassan Abd-Elhafez
Hassan Abd-Elhafez
Welded joints are sensitive to fatigue failure due to cyclic loading, as well as fatigue crack propagation influenced by the distribution of welding residual stress. In this study, the fatigue crack propagation rates in butt-welded joints for 304 stainless steel sheets were evaluated in the presence of welding residual stresses. The analysis consisted of two separate models: first, a 3D-finite element (FE) model was used to predict the residual stresses due to welding; second, a numerical study was undertaken to predict fatigue crack propagation in the presence and absence of residual stress using the extended finite element method (XFEM). The crack growth model (NASGRO) and available experimental data were applied to verify the simulation results. The XFEM without residual stress effects shows good agreement with the experimental data and the NASGRO model. However, in the presence of residual stress, the simulation results show less agreement with the NASGRO model. The level and the nature of residual stress have significant effects on crack growth. A faster crack propagation rate is recognized due to the effect of tensile residual stress at the crack tip, while a higher resistance to crack growth is developed due to a compressive residual stress field.

14 April 2022 in Materials
Verified
Journal Article
Open access
PDF file
Mohammed AlbadraniMohammed Albadrani
Mohammed Albadrani
PAParvez Ali
Parvez Ali
Waleed El-GaraihyWaleed El-Garaihy
Waleed El-Garaihy
Hassan Abd-ElhafezHassan Abd-Elhafez
Hassan Abd-Elhafez
Over the past few years, the popularity of graphene as a potential 2D material has increased since graphene-based materials have applications in a variety of fields, including medicine, engineering, energy, and the environment. A large number of graphene sheets as well as an understanding of graphene’s structural hierarchy are critical to the development of graphene-based materials. For a variety of purposes, it is essential to understand the fundamental structural properties of graphene. Molecular descriptors were used in this study to investigate graphene sheets’ structural behaviour. Based on our findings, reverse degree-based molecular descriptors can significantly affect the exchange-correlation energy prediction. For the exchange-correlation energy of graphene sheets, a linear regression analysis was conducted using the reverse general inverse sum indeg descriptor, RGISI(p,q). From RGISI(p,q), a set of reverse topological descriptors can be obtained all at once as a special case, resulting in a model with a high correlation coefficient (R between 0.896 and 0.998). Used together, these reverse descriptors are graphed in relation to their response to graphene. Based on this study’s findings, it is possible to predict the exchange correlation energy as well as the geometric structures of graphene sheets with very little computational cost.