Jiadai Xue

Dr. Jiadai Xue

orcid

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
17 December 2018 in Materials
Verified
Journal Article
Open access
PDF file
Duo LiDuo Li
Duo Li
ZQZheng Qiao
Zheng Qiao
KWKarl Walton
Karl Walton
YLYutao Liu
Yutao Liu
Jiadai XueJiadai Xue
Jiadai Xue
XJXiangqian Jiang
Xiangqian Jiang
Freeform surfaces are featured with superior optical and physical properties and are widely adopted in advanced optical systems. Slow tool servo (STS) ultra-precision machining is an enabling manufacturing technology for fabrication of non-rotationally symmetric surfaces. This work presents a theoretical and experimental study of surface topography generation in STS machining of freeform surfaces. To achieve the nanometric surface topography, a systematic approach for tool path generation was investigated, including tool path planning, tool geometry selection, and tool radius compensation. The tool radius compensation is performed only in one direction to ensure no high frequency motion is imposed on the non-dynamic axis. The development of the surface generation simulation allows the prediction of the surface topography under various tool and machining variables. Furthermore, it provides an important means for better understanding the surface generation mechanism without the need for costly trial and error tests. Machining and measurement experiments of a sinusoidal grid and microlens array sample validated the proposed tool path generation and demonstrated the effectiveness of the STS machining process to fabricate freeform surfaces with nanometric topography. The measurement results also show a uniform topography distribution over the entire surface and agree well with the simulated results.

25 September 2018 in Materials
Verified
Journal Article
Open access
PDF file
YLYutao Liu
Yutao Liu
ZQZheng Qiao
Zheng Qiao
DQDa Qu
Da Qu
YWYangong Wu
Yangong Wu
Jiadai XueJiadai Xue
Jiadai Xue
BWBo Wang
Bo Wang
Slow tool servo (STS) assisted ultra-precision diamond turning is considered as a promising machining process with high accuracy and low cost to generate the large-area micro lens arrays (MLAs) on the roller mold. However, the chatter mark is obvious at the cut-in part of every machined micro lens along the cutting direction, which is a common problem for the generation of MLAs using STS. In this study, a novel forming approach based on STS is presented to fabricate MLAs on the aluminum alloy (6061) roller mold, which is a high-efficiency machining approach in comparison to a traditional method based on STS. Based on the different distribution patterns of the discrete point of micro lens, the equal-arc method and the equal-angle method are also proposed to generate the tool path. According to a kinematic analysis of the cutting axis, the chatter mark results from the overlarge instantaneous acceleration oscillations of the cutting axis during STS diamond turning process of MLAs. Cutting parameters including the number of discrete points and cutting time of every discrete point have been experimentally investigated to reduce the chatter mark. Finally, typical MLAs (20.52-μm height and 700-μm aperture) is successfully machined with the optimal cutting parameters. The results are acquired with a fine surface quality, i.e., form error of micro lenses is 0.632 μm, which validate the feasibility of the new machining method.

1 September 2020 in Optik
Verified
Journal Article
Closed access
YJYuan Jin
Yuan Jin
林吉林省明虹科技有限公司 吉
林省明虹科技有限公司 吉
Duo LiDuo Li
Duo Li
Jiadai XueJiadai Xue
Jiadai Xue
BWBo Wang
Bo Wang
FDFei Ding
Fei Ding

22 August 2018 in Materials
Verified
Journal Article
Open access
PDF file
DQDa Qu
Da Qu
PZPeng Zhang
Peng Zhang
Jiadai XueJiadai Xue
Jiadai Xue
YFYun Fan
Yun Fan
Jiadai XueJiadai Xue
Jiadai Xue
BWBo Wang
Bo Wang
In this study, minimum quantity coolant/lubrication (MQCL) is found to have significant impact on the surface quality and mechanical properties of the micromilled thin-walled work piece that is the core component of an aeroaccelerometer. Three kinds of coolants were used in the micromilling process to analyze their effects on surface quality and mechanical properties of the component. The experiment results show that an appropriate dynamic viscosity of coolant helps to improve surface roughness. The high evaporation rate of the coolants can enhance the cooling performance. Comparing with the dry machining case, MQCL has better performance on improving tool wear, surface quality, and mechanical properties of the micromilled work piece. It yielded up to 1.4–10.4% lower surface roughness compared with the dry machining case in this experiment. The machined work piece with the best mechanical properties and the one with the worst mechanical properties appeared in the ethyl alcohol and the dry machining case, respectively. The reasons for deteriorating surface quality and mechanical properties in dry machining cases are also analyzed. For improving the micromilling process, the penetration and cooling effect of the coolants are more important. This paper gives references to obtain better service performance of the component by improving the micromilling process.

15 October 2024 in Aerospace
Verified
Journal Article
Open access
PDF file
Jiadai XueJiadai Xue
Jiadai Xue
BWBo Wang
Bo Wang
QLQiuyan Liao
Qiuyan Liao
KWKaiji Wu
Kaiji Wu
YLYutao Liu
Yutao Liu
YCYong Chen
Yong Chen
The X-ray satellite “Einstein Probe” of the Chinese Academy of Sciences (CAS) was successfully launched on 9 January 2024 at 15:03 Beijing Time from the Xichang Satellite Launch Center in China with a “Long March-2C” rocket. The Einstein Probe is equipped with two scientific X-ray telescopes. One is the Wide-field X-ray Telescope (WXT), which uses lobster-eye optics. The other is the Follow-up X-ray Telescope (FXT), a Wolter-I type telescope. These telescopes are designed to study the universe for high-energy X-rays associated with transient high-energy phenomena. The FXT consists of two modules based on 54 thin X-ray Wolter-I grazing incidence Ni-replicated mirrors produced by the Italian Media Lario company, as contributions from the European Space Agency and the Max Planck Institute for Extraterrestrial Physics (MPE), which also provided the focal-plane detectors. Meanwhile, the Institute of High Energy Physics (IHEP), together with the Harbin Institute of Technology and Xi’an Institute of Optics and Precision Mechanics, has also completed the development and production of the structural and thermal model (STM), qualification model (QM) and flight model (FM) of FXT mirrors for the Einstein Probe (EP) satellites for demonstration purposes. This paper introduces the precision manufacturing adopted in China of Wolter-I X-ray mirror mandrels similar to those used for the EP-FXT payload. Moreover, the adopted electroformed nickel replication process, based on a chemical nickel–phosphorus alloy, is reported. The final results show that the surface of the produced mandrels after demolding and the internal surface of the mirrors have been super polished to the roughness level better than 0.3 nm RMS and the surface accuracy is better than 0.2 μm, and the mirror angular resolution for single mirror shells may be as good as 17.3 arcsec HPD (Half Power Diameter), 198 arcsec W90 (90% Energy Width) @1.49 keV (Al-K line). These results demonstrate the reliability and advancement of the process. As the first efficient X-ray-focusing optics manufacturing chain established in China, we successfully developed the first focusing mirror prototype that could be used for future X-ray satellite payloads.

9 April 2025 in Micromachines
Verified
Journal Article
Open access
PDF file
Jiadai XueJiadai Xue
Jiadai Xue
YLYutao Liu
Yutao Liu
QLQiuyan Liao
Qiuyan Liao
ZLZiteng Li
Ziteng Li
FDFei Ding
Fei Ding
BWBo Wang
Bo Wang
Nickel–phosphorus (NiP) alloys have been widely used in many engineering fields such as aerospace, automotive, and optics; however, it is difficult to study the material removal mechanism and microscopic size changes in the polishing process of nickel–phosphorus alloys through simple experiments. In light of these difficulties, there is a need to improve our understanding of the surface friction and wear mechanisms of NiP materials. In the present study, molecular dynamics simulations are employed for the first time to investigate the material removal mechanism, mechanical response, phase transformation, and stress distribution of two NiP alloys with different phosphorus contents during the nano-polishing process by adjusting the polishing depth and speed. Our simulation results indicate that the mechanical response of the low-phosphorus alloy is slightly higher than that of the high-phosphorus NiP alloy. Larger polishing depths and higher speeds reduce the surface quality and lead to increased residual stress. The findings presented herein provide an atomic-level understanding of the material removal mechanism of NiP alloys via MD methodology and offer valuable guidance for selecting alloys with an appropriate NiP ratio as engineering materials and for developing processing methods to improve surface quality.