A novel three-vector-based model predictive flux control (TV-MPFC) with low computation complexity and low stator flux ripple for SPMSM is proposed, in which the stator flux vector tracking error is evaluated in the cost function, so the weighting factor used in model predictive torque control (MPTC) is eliminated, thus avoiding tedious tuning work. To enhance the steady-state performance, three voltage vectors including two active vectors and one zero vector are applied in one period, and the key improvement of the proposed strategy is to construct a novel voltage vector selection table for the second optimal active vector based on the stator flux vector error which decreases the number of candidate active vectors, thus reducing the computation complexity. The single-vector-based MPFC and four three-vector-based model predictive control algorithms are compared in this paper. The comparative experimental tests are finally implemented and the results show that the proposed TV-MPFC can enhance steady-state performance of stator flux while reducing computation complexity, hence it is more suitable for scenarios with higher requirement on stator flux.
27 February 2024 in IEEE Transactions on Industry Applications
This paper presents a multi-objective optimization design method for an electric-excitation claw-pole field-modulated (EECPFM) machine, which employs a ring-shaped excitation coil in the stator cavity formed by the claw poles, thus eliminating the slip rings and brushes, and improving the operation reliability. Due to axial asymmetry, the traditional optimization design based on 3-dimensional finite element analysis (3D-FEA) is time-consuming. The key of the proposed optimization method is to incorporate the air-gap field harmonic characteristics into the EECPFM machine design, namely, by taking the main air-gap field harmonics having strong influence on torque capability and torque ripple as multiple optimization objectives, and combing the response surface (RS) model and the artificial bee colony (ABC) algorithm to implement the optimization process, thus saving time. Subsequently, with the help of 3D-FEA, the electromagnetic performance between the initial and optimal structure are compared, i. e. 12% torque improvement and 2.8% ripple suppression. Finally, a EECPFM prototype is fabricated and the validity of the proposed optimization design is evidenced by the experiments.
26 May 2025 in IEEE Journal of Emerging and Selected Topics in Power Electronics
Due to much more available voltage vectors (VV), dual-three-phase (DTP) permanent magnet synchronous machine (PMSM) drives are more challenging in selecting the VVs than single-three-phase (STP) ones. The model predictive control (MPC) based on synthetic VVs is an excellent solution. However, its torque-speed operation range and harmonic suppression capacity at high speed are limited by the utilized synthetic VVs. In this paper, the MPC based on long (L) and medium-long (ML) VVs is proposed for DTP PMSM drives, which uses L and ML VVs directly instead of using them to construct synthetic VVs. A restraint strategy based on voltage estimation is designed to reduce the range of VV candidates and computation burden. A selection strategy based on cost functions is developed for the optimal L and ML VVs. In addition, it is verified that the optimization model for duty ratio calculation in the proposed MPC is convex. Thus, the projected quadratic programming (QP) algorithm, used in the STP drives, can be extended and used for duty ratio calculation in the proposed method, with which faster calculation than the discrete enumeration is achieved. Further, it is verified that the QP algorithm is also suitable for other MPCs for DTP PMSM drives whatever VVs are used. By using the L and ML VVs directly, the proposed MPC can not only obtain a wider torque-speed operation range than MPC based on synthetic VVs, but also realize lower current THD at high speed. Finally, experiments are conducted to verify the feasibility and advantages of the proposed method.
31 July 2025 in IEEE Transactions on Industry Applications
The flux-weakening (FW) method is employed to extend the operation speed range and maximize the torque/power capability. Compared to the feedforward FW control method, the feedback FW control method is simple and robust against parameter mismatches. In this paper, based on the field-oriented control strategy and small signal analysis, the stabilities of two forms of feedback FW control methods are investigated: d-axis current-based voltage feedback FW control (DCVFC), utilizing the dq-axis coordinate system, and current angle-based voltage feedback FW control (CAVFC), employing the polar coordinate system. Firstly, the stability characteristics of two FW control methods are analyzed in interior permanent magnet synchronous machines (IPMSMs) and surface-mounted permanent magnet synchronous machines (SPMSMs), respectively. Subsequently, comparative analyses are performed between IPMSMs and SPMSMs under the two FW control methods. Experiments are conducted on both IPMSM and SPMSM to validate the stability performance. The results indicate that there are inherent differences not only between the DCVFC and CAVFC methods when applied to the same machine but also between IPMSM and SPMSM machines when the same FW control method is utilized.
This paper introduces an enhanced approach for optimizing the flux-weakening performance of a non-salient permanent magnet synchronous machine (PMSM), by incorporating the maximum torque per voltage (MTPV) region into a conventional voltage magnitude feedback control strategy. The MTPV control strategy is initially optimized for steady-state performance by incorporating the effect of resistance, which plays a crucial role in small power motors. To maintain stability and good dynamics in the flux-weakening region, a current command feedback MTPV controller is utilized, as opposed to a voltage command feedback approach. Additionally, to address stability concerns in the MTPV region, a feedback type proportional-integral (PI) MTPV controller is designed and implemented. The stability in both the over-modulation and various flux-weakening regions is further enhanced using a voltage vector modifier (VVM). Therefore, the proposed feedback-based flux-weakening control enhances system steady-state performance, dynamic response, and stability across both linear and over modulation regions under various flux-weakening conditions, making it suitable for general-purpose applications. The effectiveness of the proposed method is validated through experimental results.