The properties of polyethylene glycol-6000 (PEG)/MgCaCO3, a low-cost shape-selective phase change material (ss-PCM), make it highly suitable for solar thermal applications. Nanosized porous MgO-doped CaCO3 with Mg molar concentrations of 5%, 10%, and 15% were synthesized using a hydrothermal technique. The prepared MgO-CaCO3 matrices were then impregnated with PEG to obtain PEG/MgCaCO3 as an ss-PCM. Samples identified as PEG-5MgCaCO3 (P-5-MCC), PEG-10MgCaCO3 (P-10-MCC), and PEG-15MgCaCO3 (P-15-MCC) were prepared and studied. Interestingly, P-10-MCC has the smallest particle size together with a good porous structure compared to the other two materials. The results of thermogravimetric analyses and differential scanning calorimetry indicate that the small particle size and porous structure facilitate the impregnation of approximately 69% of the PEG into the 10-MCC matrix. The latent heat and energy storage efficiency of PEG in the P-10-MCC sample are 152.5 J/g and 96.48%, respectively, which are significantly higher than those of comparable materials. Furthermore, in addition to the improvement of the thermal conductivity of the P-10-MCC, its supercooling is also reduced to some extent. The combined mesoporous and macro-porous structure of P-10-MCC is critical to retaining a large amount of PEG within the matrix, resulting in a high latent heat in the operating temperature range of 35–57 °C. The P-10MCC sample also demonstrates a high energy storage capacity (98.59%), high thermal energy storage/release rates, and exceptional shape-stabilized PCM properties.
13 December 2024 in Journal of Building Engineering
The development of shape-stabilized phase change materials (SS-PCMs) and their use in construction materials has demonstrated significant potential for improving building energy efficiency and reducing the power consumption of buildings, particularly in desert climates. Despite these benefits, the widespread application of PCMs in civil infrastructure is hindered by their high cost, preparation complexity, leakage issues, and low thermal conductivity. This study addresses these challenges by employing a low-cost, lightweight aggregate (LWA) as a carrier combined with polyethylene glycol (PEG) to develop an LWA/PEG composite PCM. The PEG was incorporated into the LWA pores using a vacuum impregnation technique. Analysis via X-ray diffraction (XRD) and Fourier-transform infrared spectroscopy (FTIR) confirmed that the LWA/PEG composite was successfully prepared without any chemical reactions occurring during the process. However, LWA/PEG composite suffers from leakage problems, which limit its use in building applications. Accordingly, a cement paste coating was developed and applied on LWA/PEG to prepare SS-PCM (CLWA) to prevent the leakage of the composite and enhance its thermal conductivity. Moreover, it was noted that the developed CLWA is chemically stable, and it exhibited outstanding thermal stability after 200 cycles of melting and solidification without signs of leakage. These advantageous characteristics indicate that the CLWA developed can be effectively employed to enhance the thermal efficiency of construction materials to achieve net-zero energy in buildings.
14 January 2026 in ACS Applied Engineering Materials
Developing phase change materials (PCMs) that combine high heat-storage density, fast thermal response, structural stability, and efficient solar harvesting remains a central challenge for advanced thermal energy storage and battery thermal management. In this study, a multifunctional shape-stabilized composite PCM was engineered by integrating polyethylene glycol (PEG) with hydrothermally synthesized Sr-doped BaO nanorods and graphene nanoplatelets. The design aimed to exploit the porous inorganic framework for PEG confinement while establishing synergistic heat-transfer pathways through the combined nanorod–graphene network. Sr-doped BaO supports with different Sr contents were first synthesized and incorporated into PEG, after which graphene was introduced to optimize thermal transport and photothermal response. Structural characterization confirmed successful Sr incorporation into the BaO framework and showed that PEG was physically immobilized within the support without chemical degradation. Among the support compositions, S5B-P delivered the most favorable thermal storage characteristics, with a melting enthalpy of 134.2 J/g, an impregnation ratio of 71.01%, and a heat-storage efficiency of 99.41%. Further modification with graphene substantially improved conductivity, and the optimized S5B-P10%Gn composite reached 0.79 W/m.K, representing a 92.7% increase over S5B-P, while preserving a melting enthalpy of 94.41 J/g. The composite exhibited no detectable leakage at 80 °C and retained nearly unchanged phase-transition behavior after 200 thermal cycles, confirming excellent form stability and durability. In addition, S5B-P10%Gn achieved a solar-to-thermal energy storage efficiency of 78.4%. These results demonstrate a practical strategy for constructing high-performance composite PCMs for coupled thermal storage, solar energy utilization, and battery thermal regulation.