Determining the location of objects, for example roadheader in a hard coal mine, is a task that should be automated in the conditions of state-of-the-art mining. Current solutions do not meet the user’s expectations due to the lack of the possibility of automation, maladjustment to the environment of a hard coal mine or not meeting the legal requirements. The article describes the initial stage of work on an automatic system for determining the position of machines in difficult underground conditions, including the analysis of requirements and constraints, an overview of available solutions, technologies and algorithms, as a result of which devices were selected for further tests. To determine the location, it is necessary to take distance measurements with high accuracy, despite the disturbances resulting from the working environment. Ultrasonic devices were selected and then tested under various operating conditions, including different distances between the transmitter and receiver as well as different directions and intensities of air movement that could distort the measurement results. During tests, sufficient accuracy, as well as other parameters, of the ultrasonic transducers were confirmed, allowing for distance measurements in the required range, suitable for use in the real-time locating system (RTLS) being developed.
Suspended monorails are a common mode of transportation for materials and personnel in underground mines. The goal of the EU-funded project “Innovative High Efficiency Power System for Machines and Devices, Increasing the Level of Work Safety in Underground Mining Excavations (HEETII)” is to introduce a single-wire energy transmission system combined with a capacitive-coupling-based wireless transmission system to power the suspended tractor, along with a monitoring system that will monitor the energy network and additional environmental parameters of the mine. Additionally, the monitoring system acts as the wireless communication backbone, allowing for data transmission to surface headquarters, where the data are processed and logged in a central database. This enables operators to detect and take preemptive measures to prevent potential hazards in the mine, improving the overall efficiency of the energy transmission system. This paper describes the additional considerations required for electrical systems in underground mines with potentially explosive atmospheres, as well as the design of the energy transmission system and the monitoring system.
The paper presents the results of tests of wear of hardened wear-resistant steels in the presence of quartz, coal and coal-mineral abrasives of a differentiated ratios of each component and in the case without abrasives. The tests were carried out on a ring-on-ring test stand. Volume loss was the parameter used to characterize the wear level. Based on the Scanning Electron Microscopy (SEM) observations, different mechanisms of surface destruction depending on the type of abrasive were found. For the quartz abrasive, it was shown that the quartz grains cause micro-cutting, but surface cracks also appear that further transform into shallow holes. In the case of mixtures of quartz with coal, the surface was micro-scratched by quartz grains, but some of these grains were hammered into the surface, what was favoured by the presence of coal fractions. In the case of coal abrasive, traces of single cutting were observed, as well as unremoved scratches formed at the sample grinding stage. Based on the wear observation, two models of steel surface wear in the presence of coal and coal-mineral abrasives were determined.
Perspectives of development of control system dedicated for areas threatened by methane and/or coal dust explosion hazard are presented. Development of self-powered sensors, dedicated for operation in wireless network is one of the development directions. Such a solution will complement typical control systems and it can be used in the places, where there is no possibility of using the typical sensors, in close vicinity to the machine – due to lack of wired connection. General concept of the self-powered sensors with use of two methods of power supply – piezoelectric energy harvester and thermoelectric generator, is given. Perspective of using the methods of artificial intelligence in automatic configuration of sensors network is suggested.
The article presents intelligent routing algorithms currently used in sensory networks, in terms of determining the possibility of their integration into systems working in potentially explosive atmospheres. Selected types of scribing algorithms were characterized. The analysis of simulation...
This article deals with the design, development, and analysis of a wireless power transfer system prototype based on capacitive coupling. The system is intended for the continuous charging of a suspended mine drivetrain. It consists of a resonant inverter, primary and secondary matching circuits, a suitable capacitive coupler, and a rectifier with a load, ultimately serving as a battery charger for a mobile energy storage device. The system successfully achieved the target output voltage of 320 V and a charger output power of 2 kW at an operating frequency of 300 kHz. Additionally, the total system efficiency was at the level of 60%, ensuring that the RMS voltages on passive components remained below 3 kV.