This article presents a novel control method for a multilevel dc–dc flying capacitor converter for applications in medium voltage range. Quasi-two-level modulation provides the possibility to obtain low flying capacitance even below 1 μF, whereas the triangular current mode controller part enables to achieve zero voltage switching at turn- on for a wide operating range, lowering power losses, and providing the possibility to operate at higher frequencies. The proposed novel control converges the advantages of these both methods leading to very high efficiency with high power density. Performance of the flying capacitor converter with the proposed control method is illustrated with a model-based Saber simulation at first, and then, an experimental model operating at wide frequency range (40 ÷ 250 kHz) and in medium voltage range was designed and constructed. A series of laboratory tests at up to 1.5 kV dc and 10 kW confirmed the noteworthy characteristics of the converter. The voltage between the power devices is balanced and the efficiency achieved reached as high as 99.1%. Therefore, the proposed converter can be competitively employed against classical two-level, as well as three-level and series connection-based counterparts.
This article presents a medium voltage half-bridge circuit where 3.3 kV power switches are built with two 1.7 kV/325 A SiC MOSFETs series-connected inside power modules. Essence of this work is an active balancing method eliminating the voltage imbalances between the devices by means of gate signals modification. The advantage over commonly-used passive snubbers is low cost and limited amount of additional losses. Performance of the half-bridge is illustrated with a model-based Saber simulation at first, then, an experimental full-scale model is designed with on-the-shelf power modules capable operating at power level above 150 kVA. A series of laboratory tests at 1.5 kV DC confirmed reduction of voltage differences across devices in the stack to an acceptable level - the designed system is working correctly despite EMI caused by fast switching transients. Moreover, the observed current and voltage waveforms prove the positive impact of the method as not only voltages but also switching losses are better balanced among the devices. Experimental comparison to a 3.3 kV counterpart shows two times lower turn-off energy, therefore, the presented design with two 1.7 kV SiC MOSFET power modules can beneficently compete not only in terms of lower cost but also switching performance.
This work presents the experimental validation of a 40 kW electric vehicle (EV) charger. The proposed system comprises two 20 kW modules connected in parallel at the input and output. Each module has two stages—as a grid converter Vienna Rectifier (VR) was chosen, and as an isolated DC/DC stage, two Series-Resonant Dual-Active-Bridges (SRDABs) in input-series-output-parallel (ISOP) configurations were applied. The AC/DC and DC/DC stages were enclosed in 2U rack standard housing. A bipolar DC-link with ±400 V DC voltage was employed to connect both stages of the charger module while the charger’s output is dedicated to serving 800 V batteries. VRs operated at 66 kHz switching frequency and the SRDABs operated at 100 kHz. The converters used in the charger structure were based on silicon carbide (SiC) power devices. The description and parameters of the built hardware prototypes of both—AC/DC and DC/DC—converters are provided. Moreover, the experimental validation of each stage and the whole charging system, including oscilloscope waveforms and power analyzer measurements at nominal power, are included. Such a configuration enables energy conversion with high efficiency without a negative impact on the grid and high-quality grid waveforms.
This paper discusses various solutions of energy conversion in medium voltage using power switches in Silicon Carbide (SiC) technology. In particular, a comparative study is focused on four different variants of an inverter phase leg operating at 1.5 kV DC, which has not been presented in the literature yet. The first one is based on a standard two-level half-bridge built from a 3.3 kV SiC MOSFET power module rated at 450 A. Then, the two-level solution with series-connected devices inside 1.2 kV/450 A power modules is taken into account. Finally, a flying-capacitor phase leg also based on the same 1.2 kV devices is investigated in two different modes: a standard three-level operation and quasi-two-level mode with a significantly reduced capacitor. The presented study is founded on in-depth experiments: all four phase legs were designed, built, and tested in the laboratory. All versions were connected in a half-bridge configuration with an inductive load. Tests were conducted under identical conditions to test the overall performance and switching behavior for various gate resistances. In addition, different aspects are analyzed and compared in this paper, including parasitics, cooling performance, gate drivers and layout considerations, providing selection guidelines for power switches with SiC power devices in medium voltage power electronics applications.
This article discusses an active gate driver for a 1.7 kV/325 A SiC MOSFET module. The main purpose of the driver is to adjust the gate voltage in specified moments to speed up the turn-on cycle and reduce the amount of dissipated energy. Moreover, an adequate manipulation of the gate voltage is necessary as the gate current should be reduced during the rise of the drain current to avoid overshoots and oscillations. The gate voltage is switched at the right moments on the basis of the feedback signal provided from a measurement of the voltage across the parasitic source inductance of the module. This approach simplifies the circuit and provides no additional power losses in the measuring circuit. The paper contains the theoretical background and detailed description of the active gate driver design. The model of the parasitic-based active gate driver was verified using the double-pulse procedure both in Saber simulations and laboratory experiments. The active gate driver decreases the turn-on energy of a 1.7 kV/325 A SiC MOSFET by 7% comparing to a conventional gate driver (VDS = 900 V, ID = 270 A, RG = 20 Ω). Furthermore, the proposed active gate driver lowered the turn-on cycle time from 478 to 390 ns without any serious oscillations in the main circuit.
12 October 2022 in IEEE Transactions on Industrial Electronics
This paper investigates the soft-switching quasi-square-wave (QSW) technique in DC/DC SiC-based flying capacitor converter with quasi-two-level (Q2L) control establishing design guidelines for constructing high-efficiency soft-switched bidirectional converters with low-voltage power transistors. The general idea behind the soft-switching in the proposed system is based on near-CRM (critical conduction mode) operation using TCM (triangular current mode) and Q2L control with the addition of auxiliary transistor capacitances. The soft-switching process is based on a resonance between the capacitances in parallel to each transistor, and the main inductor - ZVS at turn-on is ensured through proper modulation pattern according to TCM-Q2L control, and the turn-off soft-switching mechanism is assured through the novelty in the form of adding auxiliary capacitance in parallel to each of the SiC power MOSFETs according to QSW operation. Thus, the converter can reach very high efficiency (peak at 99.5%), maintaining soft-switching for a wide operating range, using only small auxiliary SMD capacitors and a low-volume flying capacitor, leading to high power density. The presented study is based on experimental tests using a 1.5 kV model at up to 15 kW and includes the impact of various auxiliary capacitance values and optimal capacitor value selection for maximizing the converter efficiency.