19 April 2011 in IEEE Transactions on Industrial Informatics
MKMarian P. Kazmierkowski
Power electronic Grid-Connected Converters (GCCs) are widely applied as grid interface in renewable energy sources. This paper proposes an extended Direct Power Control with Space Vector Modulation (DPC-SVM) scheme with improved operation performance under grid distortions. The real-time operated DPC-SVM scheme has to execute several important tasks as: space vector pulse width modulation, active and reactive power feedback control, grid current harmonics and voltage dips compensation. Thus, development and implementation of the DPC-SVM algorithm using single chip floating-point microcontroller TMS320F28335 is described. It combines large peripheral equipment, typical for microcontrollers, with high computation capacity characteristic for Digital Signal Processors (DSPs). The novelty of the proposed system lies in extension of the generic DPC-SVM scheme by additional higher harmonic and voltage dips compensation modules and implementation of the whole algorithm in a single chip floating point microcontroller. Overview of the laboratory setup, description of basic algorithm subtasks sequence, software optimization as well as execution time of specific program modules on fixed-point and floating-point processors are discussed. Selected oscillograms illustrating operation and robustness of the developed algorithm used in 5 kVA laboratory model of the GCC are presented.
13 December 2021 in IEEE Open Journal of Power Electronics
This paper presents a novel converterconcept of the off-board electric vehicle (EV) charging, which is based on an unfolding rectification approach where the three-phase Vienna rectifier-based unfolder (VRU) is followed by two identical isolated current-source converter (CSC) modules in input-series output-parallel configuration. The VRU operates at low frequency and thus features negligible switching losses, while the CSCs are responsible for the synthesis of the high-quality sinusoidal grid current waveforms and output voltage regulation. The proposed configuration features two time-varying soft DC-links, thus no bulky electrolytic capacitors are required. Input inductors of the CSCs limit the input current ripple, eliminating the need for separate grid filter inductors. Another notable advantage lies in the simplicity of the control system. Each CSC operates at a fixed frequency and provides the required current wave-shaping using only a single independent control variable, while no high-frequency synchronization between the two modules is required. The proposed configuration features a modular structure and was verified with a scaled 5 kW experimental prototype based on two identical 2.5 kW dc-dc modules and a common unfolding stage. During the experiments, the system provided power factor above 0.97 and THD below 5%. At rated power, the maximal efficiency of 94.8% was obtained.
26 October 2021 in IEEE Transactions on Power Electronics
This article presents a novel control method for a multilevel dc–dc flying capacitor converter for applications in medium voltage range. Quasi-two-level modulation provides the possibility to obtain low flying capacitance even below 1 μF, whereas the triangular current mode controller part enables to achieve zero voltage switching at turn- on for a wide operating range, lowering power losses, and providing the possibility to operate at higher frequencies. The proposed novel control converges the advantages of these both methods leading to very high efficiency with high power density. Performance of the flying capacitor converter with the proposed control method is illustrated with a model-based Saber simulation at first, and then, an experimental model operating at wide frequency range (40 ÷ 250 kHz) and in medium voltage range was designed and constructed. A series of laboratory tests at up to 1.5 kV dc and 10 kW confirmed the noteworthy characteristics of the converter. The voltage between the power devices is balanced and the efficiency achieved reached as high as 99.1%. Therefore, the proposed converter can be competitively employed against classical two-level, as well as three-level and series connection-based counterparts.
6 January 2021 in IEEE Access
This article presents a medium voltage half-bridge circuit where 3.3 kV power switches are built with two 1.7 kV/325 A SiC MOSFETs series-connected inside power modules. Essence of this work is an active balancing method eliminating the voltage imbalances between the devices by means of gate signals modification. The advantage over commonly-used passive snubbers is low cost and limited amount of additional losses. Performance of the half-bridge is illustrated with a model-based Saber simulation at first, then, an experimental full-scale model is designed with on-the-shelf power modules capable operating at power level above 150 kVA. A series of laboratory tests at 1.5 kV DC confirmed reduction of voltage differences across devices in the stack to an acceptable level - the designed system is working correctly despite EMI caused by fast switching transients. Moreover, the observed current and voltage waveforms prove the positive impact of the method as not only voltages but also switching losses are better balanced among the devices. Experimental comparison to a 3.3 kV counterpart shows two times lower turn-off energy, therefore, the presented design with two 1.7 kV SiC MOSFET power modules can beneficently compete not only in terms of lower cost but also switching performance.