Radek Čada

Prof. Dr. Radek Čada

VSB - Technical University of Ostrava, Faculty of Mechanical Engineering
orcid

Research Focus & Metrics

Academic Career Length

31Years (1996-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
4 June 2019 in MM Science Journal
Verified
Journal Article
Closed access
SRStanislav Rusz
Stanislav Rusz
OHOndřej Hilšer
Ondřej Hilšer
VOVladislav Ochodek
Vladislav Ochodek
Radek ČadaRadek Čada
Radek Čada
JSJiri Svec
Jiri Svec
PSPavel Szkandera
Pavel Szkandera

21 June 2017 in Journal of Medical and Biological Engineering
Verified
Journal Article
Open access
PDF file
Radek ČadaRadek Čada
Radek Čada
Karel FrydrýšekKarel Frydrýšek
Karel Frydrýšek
FSFrantišek Sejda
František Sejda
JDJiří Demel
Jiří Demel
LPLeopold Pleva
Leopold Pleva
Paper focuses on biomechanics, specifically on locking cortical bone screws in angularly stable plates used for the treatment of bone fractures in the medical fields of traumatology and orthopaedics. During extraction of titanium-alloy implants, problems are encountered in an effort to loosen some locking bone screws from the locking holes of an angularly stable plate and the subsequent stripping of the internal hexagon of the screw head. The self-locking of the screw-plate threaded joint was verified by calculation and the effect of the angle of the thread on the head of the locking cortical bone screw on self-locking was evaluated. The magnitude of the torque, causing the stripping of the internal hexagon (the Inbus type head) of a locking cortical bone screw with a shank diameter of 3.5 mm from Ti6Al4 V titanium alloy to ISO 5832-3, was determined experimentally. Also, it was experimentally found that the rotation of the screwdriver end with a hexagonal tip inside the locking cortical bone screw head during stripping of the internal hexagon causes strain of the screw head perimeter and thereby an increase of thread friction. The effect of tightening torque on the possibility of loosening of the locking cortical bone screw from the locking hole of an angularly stable plate was assessed experimentally. From the evaluation of five alternative shapes of locking cortical bone screw heads in terms of the acting stress and generated strains, it follows that the best screw is the screw with the Torx type head, which demonstrates the lowest values of reduced stress and equivalent plastic strain. Based on experiments and simulations the authors recommend that all global producers of locking cortical bone screws for locking holes of angularly stable plates use the Torx type heads, and not heads of the Inbus type or the Square, PH, PZ types.

15 June 1996 in Journal of Materials Processing Technology
Verified
Journal Article
Closed access
Radek ČadaRadek Čada
Radek Čada

1 January 2021
Verified
Conference Paper
Open access
Radek ČadaRadek Čada
Radek Čada
TPTomáš Pektor
Tomáš Pektor

30 June 2022 in Metal 2021 Conference Proeedings
Verified
Conference Paper
Open access
Radek ČadaRadek Čada
Radek Čada
TPTomáš Pektor
Tomáš Pektor
The paper deals with the design of the technology for the production of the cover stamping to achieve the minimum cost of one piece of the produced component. By calculation, the minimum values of the radius of curvature of the edge of the draw die and the edge of the draw punch were determined to eliminate the calibration operation. The shape and dimensions of the blank for the cover stamping were determined by several methods and then compared. Simulations of the drawing process allowed the locations with the greatest thinning to be analyzed and the drawability of the stamping from each alternative of the blank shape to be verified. The results of the simulations showed the highest suitability of the blank determined by the Autodesk Inventor program and also by the BSE module in Dynaform. The simulation results further demonstrated the necessity to increase the radii of curvature of the drawing edge of both the draw die and the draw punch to a value of 4 mm, which allows the fabrication of a defect-free cover stamping without the need for subsequent calibration. The use of the simulation program in the technological preparation phase of production allowed one to optimise the drawing process by a suitable design of the shape of the blank and also allowed one to design a change in the shape of the stamping which eliminated the formation of cracks at its bottom during drawing.

20 March 2024 in Archives of Civil and Mechanical Engineering
Verified
Journal Article
Closed access
PDF file
IBIwona Bednarczyk
Iwona Bednarczyk
Anna DobkowskaAnna Dobkowska
Anna Dobkowska
OHOndřej Hilšer
Ondřej Hilšer
SRStanislav Rusz
Stanislav Rusz
MPMartin Pastrňák
Martin Pastrňák
JMJarosław Mizera
Jarosław Mizera