SungJune Byun

Mr. SungJune Byun

Sungkyunkwan University, Suwon, Gyeonggi, Republic of Korea
orcid

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
16 June 2022 in Sensors
Verified
Journal Article
Open access
PDF file
SungJune ByunSungJune Byun
SungJune Byun
DKDong-Gyun Kim
Dong-Gyun Kim
KPKyung-Do Park
Kyung-Do Park
YCYeun-Jin Choi
Yeun-Jin Choi
PKPervesh Kumar
Pervesh Kumar
Kang-Yoon LeeKang-Yoon Lee
Kang-Yoon Lee
This paper presents an on-chip implementation of an analog processor-in-memory (PIM)-based convolutional neural network (CNN) in a biosensor. The operator was designed with low power to implement CNN as an on-chip device on the biosensor, which consists of plates of 32 × 32 material. In this paper, 10T SRAM-based analog PIM, which performs multiple and average (MAV) operations with multiplication and accumulation (MAC), is used as a filter to implement CNN at low power. PIM proceeds with MAV operations, with feature extraction as a filter, using an analog method. To prepare the input feature, an input matrix is formed by scanning a 32 × 32 biosensor based on a digital controller operating at 32 MHz frequency. Memory reuse techniques were applied to the analog SRAM filter, which is the core of low power implementation, and in order to accurately grasp the MAC operational efficiency and classification, we modeled and trained numerous input features based on biosignal data, confirming the classification. When the learned weight data was input, 19 mW of power was consumed during analog-based MAC operation. The implementation showed an energy efficiency of 5.38 TOPS/W and was differentiated through the implementation of 8 bits of high resolution in the 180 nm CMOS process.

10 September 2024 in IEEE Access
Verified
Journal Article
Open access
SungJune ByunSungJune Byun
SungJune Byun
DADa-Yeong Ann
Da-Yeong Ann
JJJong-Wan Jo
Jong-Wan Jo
HLHeejeong Jasmine Lee
Heejeong Jasmine Lee
YJYeon-Jae Jung
Yeon-Jae Jung
Kang-Yoon LeeKang-Yoon Lee
Kang-Yoon Lee
This paper presents a novel artificial intelligence (AI)-based phase shift system in a beamforming system implemented with field programmable gate array (FPGA)-based hardware by integrating a conventional convolutional neural network (CNN) algorithm. The position of the target can be determined through a phase shifter in a beamforming system using artificial intelligence. In a system that emits a beam from a radio frequency (RF) transmitter and receives a beam from an RF receiver, artificial intelligence can control the phase. It controls the phase of the transmitter for beam scanning and the phase to optimize the signal-to-noise ratio (SNR) of the receiver. The position of the target was detected by learning the signal input data from the receiver. Targets were detected through two-beam scanning processes in a 3D space. The first is a coarse process of detecting the approximate position of the target in the entire space, and the second is a fine process of detecting the area in detail after detecting the first approximate position. The phases of the individual antennae should be controlled for optimal beamforming based on the 5×5 antenna, and the phase is detected at high speed by holding the phase large in the first coarse tuning. The second scan entails a narrow range scan with a small phase to detect it at a high speed accurately. This study shows that with FPGA, AI beamforming can be implemented through two scanning methods without image sensors. Based on the receiver’s 5×5 antenna, the CNN input feature consisted of 35×35 classifies the class with high accuracy.

10 March 2023 in Sensors
Verified
Journal Article
Open access
PDF file
DKDong Gyu Kim
Dong Gyu Kim
SungJune ByunSungJune Byun
SungJune Byun
YPYOUNG GUN PU
YOUNG GUN PU
HHHyungki Huh
Hyungki Huh
YJYeonjae Jung
Yeonjae Jung
Kang-Yoon LeeKang-Yoon Lee
Kang-Yoon Lee
This paper proposes a high-gain low-noise current signal detection system for biosensors. When the biomaterial is attached to the biosensor, the current flowing through the bias voltage is changed so that the biomaterial can be sensed. A resistive feedback transimpedance amplifier (TIA) is used for the biosensor requiring a bias voltage. Current changes in the biosensor can be checked by plotting the current value of the biosensor in real time on the self-made graphical user interface (GUI). Even if the bias voltage changes, the input voltage of the analog to digital converter (ADC) does not change, so it is designed to plot the current of the biosensor accurately and stably. In particular, for multi-biosensors with an array structure, a method of automatically calibrating the current between biosensors by controlling the gate bias voltage of the biosensors is proposed. Input-referred noise is reduced using a high-gain TIA and chopper technique. The proposed circuit achieves 1.8 pArms input-referred noise with a gain of 160 dBΩ and is implemented in a TSMC 130 nm CMOS process. The chip area is 2.3 mm2, and the power consumption of the current sensing system is 12 mW.

24 November 2022 in Electronics
Verified
Journal Article
Open access
PDF file
PKPervesh Kumar
Pervesh Kumar
IAImran Ali
Imran Ali
DKDong Gyu Kim
Dong Gyu Kim
SungJune ByunSungJune Byun
SungJune Byun
DKDong-Gyu Kim
Dong-Gyu Kim
Kang-Yoon LeeKang-Yoon Lee
Kang-Yoon Lee
Convolutional neural networks (CNNs) have become a primary approach in the field of artificial intelligence (AI), with wide range of applications. The two computational phases for every neural network are; the training phase and the testing phase. Usually, testing is performed on high-processing hardware engines, however, the training part is still a challenge for low-power devices. There are several neural accelerators; such as graphics processing units and field-programmable-gate-arrays (FPGAs). From the design perspective, an efficient hardware engine at the register-transfer level and efficient CNN modeling at the TensorFlow level are mandatory for any type of application. Hence, we propose a comprehensive, and step-by-step design procedure for a re-configurable CNN engine. We used TensorFlow and Keras libraries for modeling in Python, whereas the register-transfer-level part was performed using Verilog. The proposed idea was synthesized, placed, and routed for 180 nm complementary metal-oxide semiconductor technology using synopsis design compiler tools. The proposed design layout occupies an area of 3.16 × 3.16 mm2. A competitive accuracy of approximately 96% was achieved for the Modified National Institute of Standards and Technology (MNIST) and Canadian Institute for Advanced Research (CIFAR-10) datasets.

16 September 2024 in IEEE Access
Verified
Journal Article
Open access
PMPhanidarapu Mounika
Phanidarapu Mounika
NANabeel Ahmad
Nabeel Ahmad
GHGhayur Hussain
Ghayur Hussain
SungJune ByunSungJune Byun
SungJune Byun
Kang-Yoon LeeKang-Yoon Lee
Kang-Yoon Lee
This paper presents the application of Artificial Intelligence (AI) to automate the intricate process of designing Sigma-Delta Analog-to-Digital Converters (SD-ADC). It explores the integration of Artificial Neural Networks (ANN) to augment the design, optimization, and operation of Sigma Delta Modulators (SDM). The core concept focuses on training ANN models to achieve the optimal design parameters for SD-ADCs. Traditional SD-ADC design approaches typically involve an iterative simulation process, wherein circuit design parameters are adjusted until the desired performance is achieved. However, this approach can be time-consuming and computationally demanding, especially when dealing with the complex SD-ADCs architectures. In response, this article proposes an alternative by replacing this manual process with the assistance of ANN models. The Proposed methodology comprises two phases. In Phase 1, the trained ANN model predicts the SD-ADC output parameters, while Phase 2 focuses on estimating the optimal input design parameters of the SD-ADC. Remarkably, the circuit’s desired parameters are derived from ANN model predictions rather than the traditional method at the architectural level. The comparative analysis between ANN, Machine Learning (ML), and traditional optimization models is performed to validate the effectiveness of the proposed model.

4 April 2025 in IEEE Open Journal of Circuits and Systems
Verified
Journal Article
Open access
SungJune ByunSungJune Byun
SungJune Byun
BJByeong-Gi Jang
Byeong-Gi Jang
JJJong-Wan Jo
Jong-Wan Jo
DCDae-Young Choi
Dae-Young Choi
YPYoung-Gun Pu
Young-Gun Pu
Kang-Yoon LeeKang-Yoon Lee
Kang-Yoon Lee
This paper presents a bidirectional Four-Switch Buck-Boost (FSBB) converter with a high-voltage (HV) gate driver for use in power bank applications. The proposed FSBB is also integrated into this converter for increased efficiency. Thus, the proposed buck-boost converter can reduce conduction loss over a wide input voltage range by reducing the on-resistance of external MOSFETs using a gate source voltage (VGS) of 5V or 10V. The chip to be examined in this study is fabricated using a 130 nm 1P5M bipolar-CMOS-DMOS HV process with laterally diffused MOSFET (LDMOS) options to have a die size of 2.7 x 2.7 mm2. The proposed architecture is found to achieve a maximum output power level of 40W. The measurement results show that the maximum efficiencies at gate-source voltages (VGS) of 5V and 10V are 96.67% and 98.15%, respectively.